Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4531
#4535

Dress With Piping

Pattern #4534

A women's fitted knee-length sheath dress with princess seams on the front and back and short cap sleeves, with decorative piping set into the princess seams and the sleeve seams. A horizontal seam under the bust on the centre front and an invisible zipper at the centre back. Drafted to your own measurements. Recommended fabric: dress fabrics made from natural or blended fibres.

Tech. Description

Dress With Piping

A women's fitted knee-length sheath dress with princess seams on the front and back and short cap sleeves, with decorative piping set into the princess seams and the sleeve seams. A horizontal seam under the bust on the centre front and an invisible zipper at the centre back.

When To Wear

  • At the office with a jacket or cardigan.
  • In summer on its own, with sandals or court shoes.

Key Design Features

Silhouette: Fitted sheath shaped by princess seams on the front and back.

Length: About knee length.

Neckline: Round, finished with an interfaced facing sewn to the shoulder seams and the centre back seam.

Sleeves: Short cap sleeves joined to the front and back by seams running from the neckline, with piping in the seam; armhole edges finished with folded bias binding turned to the inside and topstitched.

Front: Centre front cut in two parts, upper and lower, joined by a seam under the bust; side front panels joined with piped princess seams.

Back: Centre back seam with an invisible zipper; piped princess seams.

Finishing: Seams overlocked; the hem is turned up and topstitched.

Level Of Difficulty

Intermediate. Piping set evenly into curved princess and sleeve seams, an invisible zipper and bias-bound armholes.

Fabric Recommendations

Dress fabrics made from natural or blended fibres.

Additional Supplies

  • Fusible interfacing (neckline facings)
  • Invisible zipper
  • Decorative piping
  • Bias binding, 4 cm wide, for the armholes (or cut from the fabric)

Cutter's Must

If the patterns have a double contour, seam allowances are included. If the contour is single, seam allowances are not included. Seam allowances: all seams 1 cm; hem allowance for the dress bottom — 2 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90cm to 150cm) to determine how much material you will need (do not forget to account for paired and symmetrical pieces). When stitching pieces, pay attention to the notches - they must match!

From main fabric:

  • Center back piece - 2 pieces
  • Side back piece - 2 pieces
  • Side front piece — 2 pieces
  • Upper center front piece - 1 piece on fold
  • Lower center front piece – 1 piece on fold
  • Sleeve – 2 pieces
  • Back neckline facing — 2 pieces
  • Front neckline facing — 1 piece

From fusible interfacing:

  • Back neckline facing — 2 pieces
  • Front neckline facing — 1 piece

Sewing Instructions

  1. Fuse interfacing to facings.
  2. Finish the center back seam allowance separately on each piece. Stitch the center back seam from the zipper mark downwards. Press seam allowances open, pressing the opening flat. Insert the concealed zipper. Stitch the back princess seams, inserting decorative piping. Finish seam allowances and press towards the center.
  3. Stitch the upper and lower front pieces. Finish seam allowance and press upwards. Stitch the front princess seams, inserting decorative piping. Finish seam allowances and press towards the center.
  4. Attach the sleeve to the front and back, inserting decorative piping into the seam. Finish seam allowances and press towards the sleeve.
  5. Stitch the side seams. Finish seam allowances and press towards the back.
  6. Stitch the shoulder seams of the facings, press seam allowances open. Finish the outer edge. Place the facing on the neckline and stitch. Clip seam allowances and turn facings to the wrong side. Stitch the facing to the shoulder seams and the center back seam.
  7. Cut (if not ready-made) a bias binding 4 cm wide for finishing the armhole. Fold the bias binding in half lengthwise, right side out, and press. Place the binding with the armhole edge, right sides together, and stitch, then turn the binding to the wrong side and topstitch along the fold onto the main piece.
  8. Finish the bottom edge of the dress, press to the wrong side and topstitch.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?