Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4328
#4330

Fitted Collared Jacket With Sleeves

Pattern #4329

A fitted, hip-length women's jacket with princess seams front and back, a horizontal waist seam and a two-part collar whose right half is pleated and falls in a cascade down the front. Fully lined, fastened with three buttons. Drafted to your own measurements. Recommended fabric: thin, soft and pliable suiting fabric of natural or blended fibres.

Tech. Description

Fitted Collared Jacket With Sleeves

A fitted, hip-length women's jacket with princess seams front and back, a horizontal waist seam and a two-part collar whose right half is pleated and falls in a cascade down the front. Fully lined, fastened with three buttons.

When To Wear

  • Over a fitted dress or a blouse with a skirt or trousers, belted at the waist as recommended.
  • For the office and daytime events in spring and autumn.

Key Design Features

Silhouette: Fitted, shaped by princess seams on the front and back and a horizontal seam at the waist; the lower part is joined below that seam.

Length: Hip length.

Collar: Made of a left and a right part joined by a centre seam. The collar is set into the neckline and stitched to the right front edge; pleats laid on the right part form a cascade that falls to the hem.

Sleeves: Long two-piece set-in sleeves with an elbow seam and an eased cap.

Closure: Three buttons; buttonholes on the right front, buttons on the left front.

Back: Centre back seam, princess seams and darts pressed toward the centre; a separate lower part below the waist seam.

Finishing: Front edges, neckline and hem stitched with the facings; a securing line of stitching under the collar; shoulder pads and sleeve heads.

Lining: Full lining, cut from the main pattern pieces minus the facings, joined to the jacket along the waist seam line.

Level Of Difficulty

Intermediate. Princess seams, a pleated two-part collar, two-piece set-in sleeves with shoulder pads and a full bagged lining.

Fabric Recommendations

Thin, soft and pliable suiting fabric of natural or blended fibres.

Additional Supplies

  • Lining fabric
  • Fusible interfacing (centre fronts, collar, front facings, back neck facing, jacket and sleeve hems)
  • 3 buttons
  • Shoulder pads
  • Sleeve heads

Cutter's Must

From main fabric:

  • Back (center) – 2 pieces
  • Back (side) – 2 pieces
  • Front (side) – 2 pieces
  • Front (center) – 2 pieces
  • Back skirt half – 2 pieces
  • Front skirt half – 4 pieces
  • Collar (left) – 2 pieces
  • Collar (right) – 2 pieces
  • Facing (front) – 2 pieces
  • Back neck facing – 1 piece
  • Sleeve (upper) – 2 pieces
  • Sleeve (lower) – 2 pieces

From lining fabric:

  • Front (center) – 2 pieces
  • Front (side) - 2 pieces
  • Back (center) – 2 pieces
  • Back (side) – 2 pieces
  • Sleeve (upper) – 2 pieces
  • Sleeve (lower) – 2 pieces

Attention: The front and back lining pieces are cut according to the main fabric patterns, subtracting the width of the front facings and the back neck facing, respectively.

From fusible interfacing:

  • Front (center) – 2 pieces
  • Collar (left) – 1 piece
  • Collar (right) – 1 piece
  • Facing (front) – 2 pieces
  • Back neck facing – 1 piece

Sewing Instructions

  1. Fuse interfacing to the designated pieces, as well as the hem of the garment and sleeve hems.
  2. On the back, stitch and press darts towards the center. Stitch and press open the back princess seams. Stitch and press open the center back seam. Attach the back skirt half to the back.
  3. Stitch and press open the front princess seams. Attach the front skirt half to the front.
  4. Stitch and press open the shoulder and side seams of the jacket.
  5. Place the left collar with the right, right sides together, and stitch the center seam. Press seam allowances open. Place the collar pieces right sides together and stitch the ends and outer edge. Trim seam allowances at corners, clip curves. Turn the collar right side out, shape, and press. Attach the collar to the neckline and stitch to the edge of the right front opening.
  6. Stitch and press open the elbow seam of the sleeve. Press up the sleeve hem. Stitch and press open the front seam of the sleeve.
  7. Set the sleeves into the armholes, matching notches and easing the sleeve cap. Insert shoulder pads and sleeve heads.
  8. Stitch and press open the shoulder seams of the back neck facing and front facings. Stitch and press open the side seams of the inner pieces of the back and front skirt halves. On the lining fabric pieces, stitch the seams and set the sleeves, leaving an opening in the front left sleeve seam. Attach the lining to the inner edges of the front facings and the back neck facing. Attach the back and front skirt halves to the lining.
  9. Place the front facing on the right side of the front, right side down, pin, and stitch all around the front opening, neckline, and garment hem. Trim seams at corners, clip curves. Turn the jacket right side out, shape seams, and press.
  10. Attach the lining to the sleeve hem. Stitch the opening in the sleeve. Topstitch under the collar, stitching the main garment to the front facing. Secure the jacket to the lining along the attachment line of the lower parts.
  11. On the right front, make buttonholes, and on the left front, sew on buttons.
  12. Create pleats on the right collar.

Tip: The jacket is recommended to be worn with a belt.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?