Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4327
#4329

Double Breasted Jacket with Wide Lapels

Pattern #4328

A women's fitted double-breasted jacket at hip length, with a wide collar cut in one with the fronts, princess seams, two-piece sleeves, shoulder pads and a full lining. Drafted to your own measurements. Recommended fabric: suiting fabric of natural or blended fibres.

Tech. Description

Double Breasted Jacket with Wide Lapels

A women's fitted double-breasted jacket at hip length, with a wide collar cut in one with the fronts, princess seams, two-piece sleeves, shoulder pads and a full lining.

When To Wear

  • At the office with a matching skirt or trousers.
  • Over dresses and knit tops in spring and autumn.

Key Design Features

Silhouette: Fitted, shaped by princess seams on the front and back, darts on the centre fronts and centre backs, and a centre back seam; ends at the high hip.

Collar: Wide lapel collar cut in one with the centre front, joined at the centre back and set into the back neckline; the same cut-on collar is part of the facing.

Front: Double-breasted wrap with buttonholes on both fronts and two decorative buttons; an inner button on the wrong side of the right front holds the underlap. Interfaced fronts and facings.

Sleeves: Long two-piece set-in sleeves with an elbow seam, cap eased into the armhole, with sleeve heads and shoulder pads.

Back: Centre back seam, princess seams and darts; back neck facing.

Lining: Full lining cut from the main pieces minus the facings, bagged through an opening in the right sleeve seam.

Finishing: Interfaced hems of the body and sleeves, 3 cm deep.

Level Of Difficulty

Advanced. A collar cut in one with the front that needs clipping at the shoulder corner, a set-in two-piece sleeve with eased cap and sleeve heads, and a bagged full lining.

Fabric Recommendations

Suiting fabric of natural or blended fibres.

Additional Supplies

  • Lining fabric
  • Fusible interfacing (centre fronts, front facings, back neck facing, hems of body and sleeves)
  • 3 buttons (2 decorative, 1 inner)
  • Shoulder pads
  • Sleeve heads

Cutter's Must

From main fabric:

  • Back center – 2 pieces
  • Back side – 2 pieces
  • Front side – 2 pieces
  • Front center – 2 pieces
  • Front facing – 2 pieces
  • Back neck facing – 1 piece
  • Sleeve upper – 2 pieces
  • Sleeve lower – 2 pieces

From lining fabric:

  • Front center – 2 pieces
  • Front side - 2 pieces
  • Back center – 2 pieces
  • Back side – 2 pieces
  • Sleeve upper – 2 pieces
  • Sleeve lower – 2 pieces

Attention: front and back lining pieces are cut according to the main pattern pieces, subtracting the width of the front facings and the back neck facing, respectively.

From fusible interfacing: front center, front facing, back neck facing, hem and sleeve hem.

Sewing Instructions

  1. Fuse interfacing to the designated pieces.
  2. On the back center, stitch and press darts towards the center. Stitch and press darts upwards on the front center. Stitch and press open the princess seams on the front and back. Stitch and press open the center back seam.
  3. Stitch and press open the jacket side seams. Stitch shoulder seams, clip into the corner at the neckline, press seams open. Stitch the collar edge, press seams open. Attach the collar to the back neckline, press seams open.
  4. Stitch, clip into the corner, and press open the shoulder seams of the back neck facing and front facing. Stitch the collar edge, press seams open. Attach the collar to the facing neckline, press seams open.
  5. Place the front facing on the right side of the front, right side down, pin, and stitch around the front edge and the collar stand. Stitch the lower corners of the front edge. Trim seams at corners. Turn the front edges right side out, shape seams, press. Press up the garment hem.
  6. Stitch and press open the sleeve elbow seam. Press up the sleeve hem. Stitch and press open the sleeve front seam.
  7. Set sleeves into armholes, matching notches, easing the cap. Insert shoulder pads and sleeve heads.
  8. On the lining fabric pieces, stitch seams and set sleeves, leaving an opening in the right front sleeve seam.
  9. Attach the lining to the inner edges of the front facings and the back neck facing. Secure the collar attachment seam allowances close to the seams. Attach the lining to the jacket hem and the sleeve hem. Turn the jacket right side out through the opening in the sleeve. Stitch the opening in the sleeve closed.
  10. According to markings, make buttonholes on both front panels. On the left front, sew a decorative button. On the right front, sew: a decorative button on the right side, and an inner button on the wrong side.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?