Fitted Paneled Jacket with Flap Pockets
A women's fitted, fully lined hip-length jacket with short raglan-style cap sleeves, a stand collar that runs into a V-neck front, a one-button closure and flap pockets with double welts.
When To Wear
- In spring and summer over a sleeveless dress or a thin top.
- For the office with a straight skirt or trousers.
Key Design Features
Silhouette: Fitted by princess seams on the front and back.
Length: Hip length, with rounded lower front corners. The hem is faced, not turned up.
Collar: Stand collar cut in two layers (upper collar sewn into the neckline, under collar into the back neck facing), joined to the V-neck front edge.
Sleeves: Short cap sleeves cut in two parts: the back part is joined to the back, the front part to the front, with one seam over the shoulder and along the top of the sleeve. Small raglan shoulder pads.
Front: Centre front, upper side front and lower side front panels. Single-breasted, one button.
Pockets: Double-welt pockets with rounded flaps, set at the front princess seam, with lining pocket bags; the opening runs from the front into the side back piece. The pocket line is reinforced with 2 cm stay tape.
Back: Centre back seam and princess seams.
Finishing: Front edge seam allowance understitched to the facing 0.2 cm from the seam.
Lining: Full lining, sleeves included, sewn to the front facings and back facings; the jacket is turned through an opening in the left side seam of the lining.
Level Of Difficulty
Advanced. Double-welt pockets with flaps worked into a princess seam, two-part cap sleeves, a stand collar sewn to the facings and a fully bagged lining with faced hem.
Fabric Recommendations
Wool or wool-blend suiting.
Additional Supplies
- Lining fabric
- Fusible interfacing (fronts, front facings, back neck facing, upper collar)
- Stay tape, 2 cm wide
- 1 button
- Small raglan shoulder pads
Cutter's Must
From main fabric:
- Stand Collar – 2 pieces
- Side Back – 2 pieces
- Center Back – 2 pieces
- Center Front – 2 pieces
- Upper Side Front – 2 pieces
- Lower Side Front – 2 pieces
- Center Front Facing – 2 pieces
- Back Neckline Facing – 1 piece
- Back Hem Facing – 1 piece
- Back Sleeve – 2 pieces
- Front Sleeve – 2 pieces
- Flap – 2 pieces
- Pocket Frame – 4 pieces
From lining fabric:
- Center Front – 2 pieces
- Side Front – 2 pieces
- Side Back – 2 pieces
- Center Back – 2 pieces
- Back Sleeve – 2 pieces
- Front Sleeve – 2 pieces
- Big Pocket Bag – 2 pieces
- Smaller Pocket Bag – 2 pieces
From fusible interfacing:
- Front – 2 pieces
- Center Front Facing – 2 pieces
- Back Neckline Facing – 1 piece
- Stand Collar (upper collar) – 1 piece
Attention: the front, back and sleeve lining pieces are cut minus the width of the front facings and the back neckline facing respectively.
Sewing Instructions
- Fuse interfacing to the pieces listed above. Fuse stay tape along the lower edge of the Upper Side Front and the upper edge of the Lower Side Front. Fuse stay tape along the pocket position on the Side Back. The stay tape is 2 cm wide.
- Stitch the back princess seams (Center Back to Side Back) and press them open. Stitch the Back Sleeve pieces to the back.
- Stitch the Upper Side Front to the Center Front from the upper edge to the lower notch. Press the seam allowances towards the centre front. Stitch the Front Sleeve pieces to the fronts. Press the seams open.
- Stitch the underarm edges of the sleeves and the side seams in one continuous seam, ending at the lower edge of the Upper Side Front. Press the seams open. Stitch the Lower Side Front to the Side Back, aligning the pieces at the lower edge. Press the seams open.
- Fold the Flap pieces right sides together and stitch around. Clip the seam allowances on the curves, turn the flaps right side out and press.
- The pocket opening runs from the front into the side back piece. Mark the stitching line for the flap and the welts on the Side Back (matching the flap width). Fold the Pocket Frames (welts) in half lengthwise, wrong sides together, and press. Mark a guideline on each welt parallel to the fold for stitching it on. Mark a guideline on the flap parallel to its upper edge. Stitch the upper pocket bag to the flap. Stitch the welts to the jacket, starting exactly at the marked princess seam line of the front. Cut the Side Back along the line marked on the pattern. Make diagonal cuts 1–1.5 cm from the end of the pocket. Turn the welts through the opening to the wrong side, ease out the edges and adjust the welt ends so that the pressed folds meet edge to edge. Secure the pocket corners from the wrong side with a double backstitch across the base of the corners. Insert the flap into the pocket and stitch it to the upper welt. Stitch the lower pocket bag into the seam that joins the lower welt. Stitch the edges of the pocket bags together.
- Baste the welts together. Stitch the lower section of the front princess seam (Center Front to Lower Side Front), folding the pocket bags out of the way. Press the seam towards the centre front.
- Stitch the centre back seam. Press the seam open. Stitch the upper Stand Collar to the neckline. Press the seam open.
- Stitch the shoulder seams and the upper sleeve seams. Clip the seam allowances on the curves and press them open. Attach the shoulder pads.
- Stitch the under Stand Collar to the neckline of the facings. Press the seam open. Stitch the shoulder seams of the Back Neckline Facing and the Center Front Facings. Clip the seam allowances on the curves and press them open. Stitch the Back Hem Facing to the Center Front Facings. Press the seams open.
- Sew the lining pieces together and set in the lining sleeves, leaving an opening for turning in the upper part of the left side seam. Stitch the lining to the inner edges of the front facings and the back facings.
- Place the facings on the jacket, right sides together, pin, and stitch along the front edges, the upper edge of the collar and the jacket hem, stitching from the jacket side. Understitch the front edge seam allowance to the facing 0.2 cm from the seam.
- Stitch the sleeve hems to the lining in two steps. Turn the sleeves right side out and press.
- Turn the jacket right side out. Stitch the turning opening closed. Remove the pocket basting.
- On the fronts, make the buttonhole and sew on the button.