Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4527
#4529

Belted Collared Shirtdress with Patch Pockets

Pattern #4528

A fitted, knee-length women's dress with a stand collar open at the front, a short three-button placket, an inset waistband with five belt loops and patch pockets on the front and back skirt. Invisible zipper in the left side seam and a centre back vent. Drafted to your own measurements. Recommended fabric: dress fabrics made from natural or blended fibres.

Tech. Description

Collared Shirtdress

A fitted, knee-length women's dress with a stand collar open at the front, a short three-button placket, an inset waistband with five belt loops and patch pockets on the front and back skirt. Invisible zipper in the left side seam and a centre back vent.

When To Wear

  • At work, with a belt through the loops.
  • For daytime in spring and autumn, with a jacket or cardigan.

Key Design Features

Silhouette: Fitted bodice with bust and waist darts, a straight skirt.

Length: Knee length.

Collar: Interfaced stand collar with rounded ends that stop short of the centre front, leaving a V-shaped opening above the placket.

Sleeves: Three-quarter set-in sleeves with interfaced cuffs, folded in half and turned up to the right side.

Front: Bodice cut in two halves with a short placket with a rounded lower end; three buttonholes on the right placket, which is stitched over the left at its lower end.

Closure: Invisible zipper in the left side seam.

Pockets: Two large patch pockets on the front skirt with curved openings bound with self-fabric bias strips; two patch pockets with a hemmed top edge on the back.

Back: Centre back seam, a shaped yoke on the back skirt and a vent at the centre back hem.

Waist: Separate front and back waistband pieces set between bodice and skirt; five topstitched belt loops. The belt is not part of the pattern.

Finishing: Seams overlocked and pressed towards the waistband and yoke; hem turned up 2.5 cm and topstitched.

Level Of Difficulty

Intermediate. A centre back vent, a shaped placket, a stand collar, an invisible side zipper, bias-bound pocket openings and folded cuffs.

Fabric Recommendations

Dress fabrics made from natural or blended fibres.

Additional Supplies

  • Invisible zipper
  • Fusible interfacing (placket, stand collar, cuffs, vent area)
  • 3 buttons

Cutter's Must

If the patterns have a double contour, they include seam allowances. If the contour is single, the patterns do not include seam allowances. Seam allowances: all seams 1 cm. Hem allowance – 2.5 cm, back pocket top edge allowance – 2.5 cm; vent allowance – 6 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90cm to 150cm) to determine how much material you will need (do not forget to account for paired and symmetrical pieces).

From main fabric:

  • Upper Back – 2 pieces
  • Back Waistband – 1 piece
  • Lower Back – 2 pieces
  • Back Yoke – 2 pieces
  • Lower Front – 1 piece
  • Front Waistband – 1 piece
  • Upper Front – 2 pieces
  • Placket – 4 pieces
  • Stand Collar – 2 pieces
  • Sleeve – 2 pieces
  • Cuff – 2 pieces
  • Back Pocket – 2 pieces
  • Front Pocket – 2 pieces
  • Belt Loops – 1 piece (strip, cut into 5 loops later)
  • Bias strips for the front pocket openings, 4 cm wide × pocket opening length + 2 cm – 2 pieces (cut by measurement)

From fusible interfacing:

  • Placket – 2 pieces
  • Stand Collar – 1 piece
  • Cuff – 2 pieces

Sewing Instructions

When stitching pieces, pay attention to the notches - they must match!

  1. Fuse interfacing to two Placket pieces, one Stand Collar and the Cuffs.
  2. Stitch darts on back and front pieces; press waist dart depths towards the center of the pieces, and bust darts upwards.
  3. Stitch the Back Yoke to the Lower Back, press allowances towards the yoke and overlock.
  4. On the left lower back, along the vertical edge of the vent, trim 5 cm. On both lower back pieces, reinforce the vent with interfacing on the wrong side. On the right side, mark the center seam line (vent fold line). Press the left along the vent fold line; on the right, press only the allowance of the right side of the vent (6 cm) to the wrong side. Align the pieces along the center seam and secure at the upper edge of the vent. Overlock the center back edge separately on each piece. Overlock the vent allowances. Stitch the center back seam up to the vent corner. Clip the corner of the vent seam allowance on the right. Press open the center seam allowances, press the vent allowances and secure them with machine stitching.
  5. Overlock the top edge of the back pocket, press to the wrong side and topstitch. Overlock the pocket edges, press allowances to the wrong side. Place the pocket on the back according to the markings and topstitch.
  6. Stitch the Back Waistband to the Upper Back, press allowances towards the waistband and overlock. Stitch the lower back (with the yoke) to the Back Waistband, press allowances towards the waistband and overlock.
  7. Cut a bias strip 4 cm wide and a length equal to the front pocket opening length + 2 cm. Fold the bias strip in half lengthwise, right side out, and press. Place the bias strip on the right side of the Front Pocket along the pocket opening, letting the ends extend, and stitch. Turn the bias strip to the wrong side, clip the seam allowances and topstitch along the fold onto the pocket. Press the pocket.
  8. Overlock the remaining outer edges of the Front Pocket and press the allowances to the wrong side. Place the pocket on the front according to the markings and topstitch.
  9. Fold placket pieces in pairs, right sides together, and stitch the outer edge. Clip allowances at the curve. Turn pieces right side out and press. Attach the outer placket to the front, fold the allowance of the inner placket inwards and topstitch into the seam of the outer placket. Work the buttonholes on the right placket according to the markings. Place the right placket over the left and secure at the lower edge.
  10. Stitch the Front Waistband to the Upper Front, press allowances towards the waistband and overlock. Stitch the Lower Front to the Front Waistband, press allowances towards the waistband and overlock.
  11. Stitch shoulder and right side seams, press allowances towards the back and overlock. Overlock left side seams separately on each piece. Stitch the left side seam from the armhole to the mark and from the zipper mark to the bottom. Insert the invisible zipper.
  12. Place the Stand Collar pieces right sides together and stitch along the outer edge (start and end the stitching exactly at the marked neckline seam line). Clip the allowances, turn the stand right side out and press. Stitch the outer stand to the neckline, fold under the allowance of the inner stand and stitch it in the ditch of the outer stand seam.
  13. Stitch sleeve seams, press allowances and overlock. Stitch cuff into a loop, press open allowances. Press cuff lengthwise in half, right side out. Place the cuff against the wrong side of the sleeve and stitch. Overlock allowances, turn cuff right side out.
  14. Set sleeves into armholes, press allowances and overlock.
  15. Overlock the bottom edge of the garment, press to the wrong side and topstitch. Sew on buttons.
  16. Overlock one long edge of the Belt Loops strip. Fold the strip in three and topstitch along both long sides. Cut it into 5 loops. Stitch the loops at the waist as shown in the technical drawing.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?