Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4502
#4504

Waisted Flounce Skirt with Back Vent

Pattern #4503

A women's fitted pencil skirt with a wide interfaced waistband, an asymmetric flounce at the hip that runs into a front princess seam, a pleated back flounce, and a centre back vent trimmed with buttons. Lined. Drafted to your own measurements. Recommended fabric: fine, well-draping double-faced wool fabrics of natural or blended fibres: the flounces show both sides of the fabric.

Tech. Description

Waisted Flounce Skirt with Back Vent

A women's fitted pencil skirt with a wide interfaced waistband, an asymmetric flounce at the hip that runs into a front princess seam, a pleated back flounce, and a centre back vent trimmed with buttons. Lined.

When To Wear

  • To the office in autumn and spring, with a fitted blouse or knit tucked in.
  • For daytime events, with a short jacket that leaves the waistband visible.

Key Design Features

Silhouette: Fitted pencil skirt, narrowing towards the hem.

Length: Below the knee.

Waist: Wide straight waistband with four buttons at the front; it fastens at the centre back with one button and buttonhole.

Front: Separate right and left front panels shaped with darts and joined by an off-centre princess seam. The front flounce is caught into the waist seam and into this princess seam, falling in a cascade.

Back: Darts, a centre back seam with a concealed zip, a flounce with pressed pleats below the waistband, and a vent at the hem fastened with three buttons.

Finishing: Lower edges of the flounces bound with decorative trim; hem turned up 2 cm and topstitched.

Lining: Skirt lining with darts, attached at the waist; lining hem turned and topstitched separately.

Level Of Difficulty

Intermediate. A lined skirt with a vent, a concealed zip, flounces set into a princess seam, trimmed edges and a buttoned waistband.

Fabric Recommendations

Fine, well-draping double-faced wool fabrics of natural or blended fibres: the flounces show both sides of the fabric.

Additional Supplies

  • Lining fabric
  • Fusible interfacing (waistband)
  • 8 buttons
  • 1 concealed zip
  • Decorative tape for the flounce edges (length marked on the front panel pattern piece)

Cutter's Must

From main fabric:

  • 1. Right front – 1 piece
  • 2. Left front – 1 piece
  • 3. Back – 2 pieces
  • 4. Right front flounce – 1 piece
  • 5. Left front flounce – 1 piece
  • 6. Back flounce – 2 pieces
  • 7. Waistband – 1 piece

From fusible interfacing:

  • 1. Waistband – 1 piece

From lining fabric:

  • 1. Front skirt lining – 1 piece on fold
  • 2. Back skirt lining – 2 pieces

Sewing Instructions

  1. Fuse fusible interfacing to the waistband.
  2. Stitch darts on the front and back panels. Press dart bulk towards the center.
  3. Stitch side seams. Finish seam allowances and press towards the back.
  4. Stitch flounce side seams. Finish seam allowances and press towards the back. Finish the lower edges of the flounce with decorative trim strip. Place the flounce on the skirt, aligning the upper edge and the front princess seam.
  5. Stitch the front princess seam. Finish seam allowances and press open.
  6. Stitch darts on the lining. Press dart bulk towards the center. Stitch the center back seam of the lining from the zipper notches to the hem. Press seam allowances open. Stitch and finish side seams. Press seam allowances towards the back. Finish the lower seam allowance of the lining, fold inwards, and topstitch.
  7. Baste the upper edge of the skirt, flounce, and skirt lining together.
  8. Finish the seam allowances of the center back seam of the back and the flounce seam, simultaneously finishing the vent. Stitch the center back seam from the zipper mark to the edge of the vent. Press the seam seam allowances open, pressing the zipper opening flat, and press the vent seam allowances towards the left side seam. Press the right side of the vent 1 cm and topstitch. Secure the vent seam allowances with machine stitching. Insert the zipper.
  9. Attach the waistband to the upper edge of the skirt. Finish the ends of the waistband, trim seam allowances at the corners, and turn right side out. Fold the inner edge of the waistband and topstitch in the ditch of the attachment seam. Press the waistband when finished.
  10. Finish the lower edge of the skirt, press to the wrong side, and topstitch.
  11. Mark and finish the buttonhole on the waistband. Sew buttons to the waistband and vent according to the marks.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Additional options

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?