Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4503
#4505

Wrap-Front Sheath Dress with Stand Collar and Pleated Bodice

Pattern #4504

A fitted women's sheath dress with short set-in sleeves, a crossover V-neck bodice and a stand collar at the back neck. The left front is pleated at the side and laid over the right; below it, a shaped front insert and a straight skirt with a centre back vent. Drafted to your own measurements. Recommended fabric: soft, pliable dress fabrics of natural or blended fibres that hold small pleats.

Tech. Description

Wrap-Front Sheath Dress with Stand Collar and Pleated Bodice

A fitted women's sheath dress with short set-in sleeves, a crossover V-neck bodice and a stand collar at the back neck. The left front is pleated at the side and laid over the right; below it, a shaped front insert and a straight skirt with a centre back vent.

When To Wear

  • To the office and business meetings in spring, summer and early autumn.
  • For daytime events and dinners, with heels and a clutch.

Key Design Features

Silhouette: Close-fitting sheath.

Length: Knee length.

Neckline: Crossover V-neck. The front neck edges are finished with interfaced facings; a two-layer stand collar is set into the back neckline and ends at the shoulder seams.

Sleeves: Short one-piece set-in sleeves, eased into the armhole.

Front: Upper right front shaped with a dart; upper left front gathered into pleats at the side seam, pressed downwards, and stitched over the right. A front insert joins the bodice to the lower front at the waist.

Back: Waist and shoulder darts, centre back seam with a vent at the hem.

Closure: Concealed zip in the centre back seam.

Finishing: Dress and sleeve hems turned up 2 cm and blind-stitched by hand; vent allowance secured to the hem.

Level Of Difficulty

Intermediate. A pleated crossover bodice with faced edges, a stand collar set between the shoulder seams, a back vent and a concealed zip.

Fabric Recommendations

Soft, pliable dress fabrics of natural or blended fibres that hold small pleats.

Additional Supplies

  • Concealed zip
  • Fusible interfacing (stand collar, front facings, vent)

Cutter's Must

From main fabric:

  • Back - 2 pieces
  • Upper right front – 1 piece
  • Upper left front – 1 piece
  • Front insert – 1 piece
  • Lower front - 1 piece
  • Collar stand – 4 pieces
  • Right front facing – 1 piece
  • Left front facing – 1 piece
  • Sleeve - 2 pieces

From fusible interfacing:

  • Collar stand — 1 piece
  • Right front facing – 1 piece
  • Left front facing – 1 piece

Sewing Instructions

  1. Fuse fusible interfacing to the designated pieces.
  2. Stitch the waist and shoulder darts on the back pieces. Press dart allowances towards the center seam.
  3. Stitch the outer collar stands to the back neckline, clip the seam allowances, and press towards the collar stand.
  4. On the left back, cut 5 cm along the vertical slit edge. On both back pieces, fuse the slit from the wrong side. On the right side, mark the center seam line (slit fold line). Press the left along the slit fold line; on the right, press only the right slit allowance (6 cm) to the wrong side. Align the pieces along the center seam and secure at the upper slit edge. Overlock the center back edge separately on each piece. Overlock the slit seam allowances. Stitch the center back edge from the mark to the slit corner. Clip the corner of the slit seam allowance on the right. Press the center seam allowances open, press the slit allowances and secure them on the right side with machine stitching. Insert the zipper.
  5. Stitch the dart on the upper right front, press the dart allowance towards the center. Overlock the lower edge of the right front facing, place it with the upper front and stitch the neckline edge. Turn the facing to the wrong side, press.
  6. Form and secure the pleats on the upper left front, with the depths directed downwards. Place the left front facing with the upper left front and stitch the upper edge. Clip the seam allowances at the curves, turn the facing to the wrong side, smooth, and press.
  7. Place the upper left front over the right, align the lower edge of the left front with the lower edge of the right facing and stitch. Overlock the seam allowances. Topstitch the right facing onto the left front, folding back the right front.
  8. Stitch the front insert to the lower front, press seam allowances upwards and overlock. Stitch the upper and lower front parts, press seam allowances upwards and overlock.
  9. Stitch the side edges, press seam allowances towards the back and overlock.
  10. Press the lower allowance of the inner collar stand to the wrong side. Place the inner collar stand with the outer collar stand right sides together and stitch the upper edge exactly to the marked shoulder seam line. Clip the seam allowances.
  11. Stitch the shoulder edges, placing them between the outer and inner collar stands. Press seam allowances towards the back, overlock. Turn the pieces to the right side. Topstitch the inner collar stand into the seam of the outer collar stand attachment.
  12. Stitch the sleeve edge. Press seam allowances and overlock. Set the sleeves into the armholes, aligning the notches and easing the cap. Press seam allowances and overlock.
  13. Overlock the hem allowance of the dress and sleeve, press to the wrong side and hem with blind stitches. Secure the slit allowance to the hem.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?