Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4491
#4493

Fitted Vest with Piped Princess Seams, Welt Pockets

Pattern #4492

A fitted, fully lined women's vest with a deep square neckline, princess seams front and back trimmed with contrast piping, two welt pockets and a four-button front. Drafted to your own measurements. Recommended fabric: suiting fabrics in natural or blended fibres, with a companion fabric.

Tech. Description

Fitted Vest with Piped Princess Seams, Welt Pockets

A fitted, fully lined women's vest with a deep square neckline, princess seams front and back trimmed with contrast piping, two welt pockets and a four-button front.

When To Wear

  • Over a blouse or shirt with suit trousers or a skirt for the office.
  • As part of a three-piece suit with a matching jacket.
  • Over a fine knit top in spring and autumn.

Key Design Features

Silhouette: Close-fitting, shaped by princess seams on the fronts and back.

Length: Waist to upper hip, with the front hem cut to two points below the buttons.

Neckline: Deep square neckline with rounded corners, finished with a facing and edged with piping.

Sleeves: Sleeveless; the armholes are faced with the lining.

Closure: Single-breasted, four buttons, buttonholes on the right front.

Pockets: One welt pocket on each front, the welt stitched down along its short sides.

Back: Centre back seam and princess seams with piping; a piped back neck facing and a shaped hem with a centre notch.

Finishing: Piping is inserted into the princess seams and the neckline seam; the neckline allowance is understitched to the lining at 0.2 cm.

Lining: Full lining with hem facings, bagged out through an opening in the left side seam.

Level Of Difficulty

Intermediate. Inserting piping into curved princess seams and the neckline, welt pockets, and bagging out a lined vest with the armholes stitched through the side-seam opening.

Fabric Recommendations

Suiting fabrics in natural or blended fibres, with a companion fabric.

Additional Supplies

  • Lining fabric
  • Fusible interfacing (front facings, neckline facings, welts)
  • 4 buttons
  • Decorative piping

Cutter's Must

From main fabric:

  • Back center – 2 pieces
  • Back side – 2 pieces
  • Front center - 2 pieces
  • Front side – 2 pieces
  • Back neckline facing – 2 pieces
  • Front neckline facing – 2 pieces
  • Back hem facing — 2 pieces
  • Front side facing — 2 pieces
  • Front facing — 2 pieces
  • Welt pocket flap – 2 pieces

From lining fabric:

  • Lining of back center – 2 pieces
  • Lining of back side – 2 pieces
  • Lining of front side – 2 pieces
  • From fusible interfacing: front facing, back neckline facing, front neckline facing, welt pocket flaps.

Sewing Instructions

  1. Fuse interfacing to the pieces.
  2. Stitch the princess seams of the front, inserting decorative piping. Press seam allowances towards the center of the front.
  3. Stitch the center back seam of the back. Press the seam to the left side. Stitch the princess seams of the back, inserting decorative piping. Press seam allowances towards the center of the back.
  4. Stitch the shoulder and side seams. Press seam allowances towards the back.
  5. Stitch the shoulder seams of the neckline facing. Press seam allowances open. Stitch the facing to the neckline, inserting decorative piping. Clip the seam allowances at curves and press.
  6. Fold the welt pocket flap right sides together and stitch the short sides. Trim seam allowances and turn right side out. Overlock the bottom edge. Place the welt pocket flap on the front, aligning the stitching line with the lower marking line (the fold of the welt pocket flap is directed towards the bottom edge) and topstitch. Turn the welt pocket flap up and topstitch along the two short sides.
  7. Stitch the princess seams of the back lining. Stitch the center seam. Stitch the inner facing to the back lining. Stitch the hem facings to the lining pieces. Press seam allowances upwards. Stitch the lining pieces similarly to the main pieces, leaving an opening in the left side seam. Place the garment with the lining right sides together and stitch along the front edge, neckline, and hem. Clip the seam allowances at curves, topstitch the neckline seam allowance to the lining at 0.2 cm.
  8. Stitch the armhole in 2 steps through the opening in the side seam: the back armhole from the shoulder seam to the side seam, and the front armhole from the shoulder seam to the side seam. Close the opening.
  9. On the right front, make buttonholes; on the left front, sew on buttons.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?