Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4492
#4494

Fitted Asymmetric Peplum Top

Pattern #4493

A fitted women's top with a waist seam, three-quarter set-in sleeves and an asymmetric peplum: the lower right front overlaps the lower left front and ends in a point. Round neckline finished with facings, invisible zipper at the centre back. Drafted to your own measurements. Recommended fabric: firm blouse fabrics made from natural or blended fibres.

Tech. Description

Fitted Asymmetric Peplum Top

A fitted women's top with a waist seam, three-quarter set-in sleeves and an asymmetric peplum: the lower right front overlaps the lower left front and ends in a point. Round neckline finished with facings, invisible zipper at the centre back.

When To Wear

  • For the office, tucked under a jacket or worn on its own with a pencil skirt or straight trousers.
  • In spring and autumn, when three-quarter sleeves are enough.

Key Design Features

Silhouette: Close-fitting bodice shaped with darts, joined at the waist to a peplum that covers the hips.

Length: Below the hip; the overlapping front falls lower than the back and ends in a point.

Neckline: Round, finished with front and back neck facings interfaced with fusible interfacing.

Sleeves: One-piece set-in sleeves, three-quarter length, with a 2 cm hem.

Front: The upper front is one piece with waist darts and bust darts. The lower front is cut as two pieces: the right part overlaps the left one, the two are joined along the marked centre line from the waist seam down to a mark, and below it the right part hangs free. Both centre edges are turned under 2 cm and topstitched.

Back: Upper and lower back, each in two halves, with a waist seam and waist darts on the upper back. Centre back seam with an invisible zipper from the neckline.

Finishing: Waist seam allowances pressed up; shoulder and side seams pressed towards the back; hems turned up 2 cm and topstitched.

Level Of Difficulty

Intermediate. Waist and bust darts, an invisible zipper, faced neckline and the overlapping lower front, which has to be matched exactly to the marked lines.

Fabric Recommendations

Firm blouse fabrics made from natural or blended fibres.

Additional Supplies

  • Fusible interfacing (neck facings)
  • Invisible zipper

Cutter's Must

From main fabric:

  • Upper Back – 2 pieces
  • Lower Back – 2 pieces
  • Upper Front – 1 piece
  • Lower Right Front – 1 piece
  • Lower Left Front – 1 piece
  • Sleeve – 2 pieces
  • Front Neck Facing – 1 piece
  • Back Neckline Facing – 2 pieces

From fusible interfacing:

  • Front Neck Facing – 1 piece
  • Back Neckline Facing – 2 pieces

Sewing Instructions

  1. Fuse interfacing to the Front Neck Facing and Back Neckline Facing.
  2. On the back pieces, stitch the waist darts. Press dart depths towards the center. Attach the lower back to the upper back, press seam allowances upwards and serge.
  3. Serge the center back edges separately. Stitch the center back seam from the zipper mark downwards, press the seam allowances open. Insert the invisible zipper.
  4. On the upper front piece, stitch the waist and bust darts. Press waist dart depths towards the center, and bust darts upwards.
  5. Serge the center edges of the Lower Right Front and Lower Left Front. Press the center edge allowance of the Lower Left Front to the wrong side and topstitch. Place the Lower Right Front on the Lower Left Front, right sides together, matching the marked allowance line on the center edge of the right piece with the marking on the left piece, and stitch from the upper edge down to the mark. Fold the right piece over to the right side and press the seam, pressing under the center edge allowance of the Lower Right Front. Topstitch the pressed allowance, folding the left piece out of the way.
  6. Stitch the lower front to the Upper Front, press seam allowances upwards and serge.
  7. Stitch the shoulder and side seams. Press seam allowances towards the back and serge.
  8. Stitch the shoulder seams of the facings, press seam allowances open. Serge the outer edge. Place the facings with the garment right sides together and stitch the neckline edge. Clip the seam allowances at curves, turn the facings to the wrong side and press. Secure the facings to the shoulder seams and the zipper tape.
  9. Stitch the sleeve seam, press seam allowances and serge. Set the sleeves into the armholes, aligning notches. Press seam allowances and serge.
  10. Serge the hem of the garment and sleeves, press to the wrong side and topstitch.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?