Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4490
#4492

Relaxed Hooded Coat

Pattern #4491

An unlined women's coat in a relaxed cocoon shape with a rounded hem, a two-piece hood set into the neckline and edge-to-edge fronts held by one hook-and-eye. The whole outer edge is bound with a folded band and decorative piping. Drafted to your own measurements. Recommended fabric: soft, pliable coating fabrics made from natural or blended fibres.

Tech. Description

Relaxed Hooded Coat

An unlined women's coat in a relaxed cocoon shape with a rounded hem, a two-piece hood set into the neckline and edge-to-edge fronts held by one hook-and-eye. The whole outer edge is bound with a folded band and decorative piping.

When To Wear

  • In mild autumn and spring weather, over knitwear, dresses or trousers.
  • As a light outer layer for everyday wear, with the hood up in wind or drizzle.

Key Design Features

Silhouette: Relaxed, rounded through the body and narrowing towards the hem.

Length: Mid-thigh, with a curved hemline.

Collar: No collar; a hood with a centre seam is sewn into the neckline and its front edges continue into the front edges of the coat.

Sleeves: Long set-in sleeves, sewn together with the side seam in one pass, with cuffs shaped by darts.

Front: Edge-to-edge fronts with a dart on each front, fastened with one hook-and-eye at the cross mark.

Pockets: Slanted single-welt pockets in the fronts; the welts are interfaced and the pocket bags are cut from lining fabric.

Back: Centre back seam.

Finishing: Decorative piping is stitched along the outer edge of the fronts, hood and hem; a folded edge band joined into a ring is sewn over it, and the seam allowance is covered with bias tape and topstitched.

Lining: Unlined; only the pocket bags are in lining fabric.

Level Of Difficulty

Intermediate. Welt pockets with two pocket bags, a hood set into the neckline, and one continuous edge band with piping and bias tape around the whole coat.

Fabric Recommendations

Soft, pliable coating fabrics made from natural or blended fibres.

Additional Supplies

  • Hook-and-eye fastener
  • Decorative piping (length marked on the front pattern piece)
  • Bias tape (length marked on the front pattern piece)
  • Lining fabric (pocket bags)
  • Fusible interfacing (welts, pocket openings)

Cutter's Must

From main fabric:

  • Back – 2 pieces
  • Front – 2 pieces
  • Sleeve – 2 pieces
  • Cuff – 2 pieces
  • Hood – 2 pieces
  • Piping (edge band) – 2 pieces
  • Off-Set Welt – 2 pieces

From lining fabric:

  • Bigger Pocket Bag – 2 pieces
  • Smaller Pocket Bag – 2 pieces

From fusible interfacing:

  • Off-Set Welt – 2 pieces

Sewing Instructions

  1. Stitch the dart on the front. Press the depth downwards.
  2. Fuse interfacing to the Off-Set Welts. Mark the pocket placement and fuse a strip of interfacing over the pocket opening. Press the welt in half lengthwise, wrong sides together. Stitch the Smaller Pocket Bag to the inner layer of the welt. Stitch the welt to the front along the lower pocket marking line. Stitch the Bigger Pocket Bag to the front along the upper pocket marking line. The ends of the stitches should finish at the short marking lines. Cut open the pocket opening. Clip diagonally into the corners, starting 1–1.5 cm from each end of the opening. Turn the welt and large pocket bag to the wrong side through the opening. Secure the ends of the pocket from the wrong side with a double backstitch at the base of the corners. Stitch and serge the pocket bag edges.
  3. Stitch the center back seam. Serge the seam allowance and press to the left side.
  4. Stitch the shoulder seams of the coat. Serge the seam allowances and press towards the back.
  5. Stitch the center seam of the Hood. Serge the seam allowance and press to the left side. Attach the hood to the neckline. Serge the seam allowance.
  6. Stitch the darts on the Cuff and trim the dart depths with the serger. Stitch the cuff to the sleeve. Serge the seam allowance and press towards the sleeve. Attach the sleeves to the armholes. Serge the seam allowance.
  7. Stitch the side seam simultaneously with the sleeve seam. Serge the seam allowance and press towards the back.
  8. Stitch the decorative piping along the outer edge of the coat. Join the short ends of the Piping (edge band) pieces into a ring. Fold the band in half lengthwise and press. Place it on the right side of the coat and stitch around the whole edge. Open out the bias tape and place it over the seam. Stitch the bias tape. Turn the seam allowance and bias tape towards the coat and topstitch, covering the seam allowance.
  9. Sew on the hook-and-eye at the cross mark.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?