Stand Collar V-Neck Coat
A knee-length women's coat with a stand collar rising from a V-shaped front neckline, a concealed fly-front closure with five buttons and a centre back vent. Two-piece set-in sleeves; fully lined.
When To Wear
- Over dresses and suits in spring and autumn.
- To the office and to daytime events, with heeled shoes.
Key Design Features
Silhouette: Semi-fitted, shaped by long curved darts on the fronts and darts on the back. Below the closure the front edges angle apart towards the hem.
Length: Knee length.
Collar: Stand collar continuing the front neckline; the back stand is a separate interfaced piece joined to the fronts at the shoulder seams.
Sleeves: Two-piece set-in sleeves, slightly shortened, with interfaced hems.
Closure: Fly front: five buttonholes worked in a framed opening on the right front facing, with bar tacks between them; the fly is held by a line of topstitching on the right front.
Back: Centre back seam ending in a vent; darts on each back piece.
Finishing: Fully interfaced fronts, facings and stand; interfaced back armhole allowances, coat hem and sleeve hems; shoulder pads.
Lining: Full lining cut from the main pieces less the facings, attached to the hem, the vent and the sleeve hems.
Level Of Difficulty
Advanced. A framed fly-front opening with buttonholes and bar tacks, a lined back vent, a stand collar joined through the shoulder seams and two-piece sleeves.
Fabric Recommendations
Suiting fabrics of natural or blended fibres.
Additional Supplies
- Lining fabric
- Fusible interfacing (fronts, facings, collar stand, back neck facing, fly lining, hems, back armhole allowances)
- 5 buttons
- Shoulder pads
Cutter's Must
From main fabric:
- Back – 2 pieces
- Front – 2 pieces
- Collar stand – 2 pieces
- Upper sleeve – 2 pieces
- Lower sleeve – 2 pieces
- Back neckline facing – 1 piece
- Front facing – 2 pieces
From lining fabric:
- Back – 2 pieces
- Front – 2 pieces
- Upper sleeve – 2 pieces
- Lower sleeve – 2 pieces
- Fly fastening lining – 2 pieces
- Attention: The back and front lining pieces are cut according to the main pattern pieces, subtracting the back neckline facing and front facing respectively.
From fusible interfacing:
- Front – 2 pieces
- Front facing — 2 pieces
- Collar stand – 1 piece
- Back neckline facing — 1 piece
- Fly fastening lining – 1 piece
- Also, the back armhole seam allowances, garment hem, and sleeve hem are interfaced.
Sewing Instructions
- Fuse fusible interfacing to the designated pieces.
- Stitch the darts on the back, press the fullness towards the center. On the wrong side of the back pieces, interface the vent. On the right side, mark the center seam line (the vent fold line). Press the left back along the vent fold line. Align the pieces along the center seam. Stitch the center seam of the back and the vent corner, stopping 1 cm before the vertical vent edge. Clip the vent seam allowance corner on the right piece. Press the center seam allowances open, press the vent allowances and secure them on the right side with machine stitching.
- Stitch the darts on the front, clip the seam allowances at the curves and press them open.
- Attach the outer collar stand to the back neckline, clip the seam allowances and press them open.
- Stitch the shoulder seams of the coat simultaneously with the collar stand seam, clip the seam allowances and press them open. Stitch the side seams, press the seam allowances open.
- Mark the fly fastening slit on the right front facing with three lines: the first line is parallel to the front edge and is 1.5 cm from the finished front edge; the second and third lines define the length of the fastening. Place the interfaced lining on the right side of the front facing, right side down, moving from the front edge, aligning the lining edge and the marked line. Stitch 0.5 cm from the marked line along the fastening slit up to the lines defining the fastening length. Place the second fastening lining flush with the stitching of the first lining and stitch 0.5 cm away. Check the correctness of the lining attachment from the wrong side (the stitches should be parallel). Cut the opening. Make diagonal cuts 1-1.5 cm from the end of the fastening slit. Turn the lining through the created opening to the wrong side, forming a frame from the interfaced lining equal to the width between the stitches. Stitch a securing stitch into the lining attachment seam. Press the second lining towards the inner edge of the front facing and stitch a securing stitch 0.1 cm from the lining attachment seam. Mark and make the buttonholes. Buttonholes are made on the front facing together with the interfaced lining. Straighten and secure the ends of the fastening from the wrong side with a double backstitch at the base of the corners. Stitch the lining edges. Place bar tacks between each pair of buttonholes, the length of the bar tack is equal to the width of the frame. Press the front facing.
- Attach the inner collar stand to the facing neckline, clip the seam allowances and press them open. Stitch the shoulder seams of the front facings and facing, simultaneously with the collar stand seam, press the seam allowances open.
- Press up the hem allowance. Place the front facing on the right side of the front, right side down, and stitch the front edges and the collar stand edge. Stitch the corner of the front edge, stopping 1.5 cm before the inner edge of the front facing. Trim the seam allowances at the corners, turn the front edges and collar stand to the right side, and straighten the seams.
- Stitch and press open the elbow seam of the sleeve. Press up the sleeve hem. Stitch and press open the front seam of the sleeve. Set the sleeve into the armhole. Attach the shoulder pads.
- On the lining fabric pieces, stitch the seams, leaving an opening in the left side seam for subsequent turning. Attach the sleeves. Attach the lining to the front facings and facing.
- Attach the lining to the garment hem, vent, and sleeve hem. Turn the coat through the opening. Close the opening.
- Stitch a topstitch on the right front according to the markings, securing the fly fastening. Sew on buttons corresponding to the buttonholes.