Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4416
#4419

Fitted Stand Collar Coat

Pattern #4417

A women's fitted single-breasted coat, just above knee length, with a stand collar that buttons at the front, curved front yokes, princess seams front and back, and pockets set into the front princess seams. Fully lined. Drafted to your own measurements. Recommended fabric: coating fabrics of natural or blended fibres.

Tech. Description

Fitted Stand Collar Coat

A women's fitted single-breasted coat, just above knee length, with a stand collar that buttons at the front, curved front yokes, princess seams front and back, and pockets set into the front princess seams. Fully lined.

When To Wear

  • In autumn and spring over dresses, skirts or slim trousers.
  • For work and city wear; the stand collar closes high at the neck in cold wind.

Key Design Features

Silhouette: Fitted through the waist by princess seams on the fronts and back, slightly widening to the hem.

Length: Just above the knee.

Collar: Stand collar with outer and inner layers, topstitched along the upper edge; it continues the front overlap and fastens with a button.

Sleeves: Long two-piece set-in sleeves; the upper sleeve cap is pressed towards the neckline and topstitched 5 cm either side of the shoulder seam.

Closure: Single-breasted, buttons and buttonholes from the collar to below the waist.

Front: A curved yoke on each front runs from the armhole to the centre front and is topstitched; princess seams run from the yoke to the hem.

Pockets: In-seam pockets in the front princess seams, topstitched along the pocket opening; pocket bags cut from lining.

Back: Centre back seam, princess seams from the armholes, and darts topstitched 0.5 cm from the seam.

Finishing: Front edges topstitched; front facings and back neck facing; centre fronts, facings, back armholes, pocket openings and hem interfaced; shoulder pads.

Lining: Full lining, cut from the coat pieces less the facings.

Level Of Difficulty

Intermediate. Princess seams with in-seam pockets, a two-layer stand collar set between the coat and the facings, two-piece sleeves, a bagged lining, buttonholes.

Fabric Recommendations

Coating fabrics of natural or blended fibres.

Additional Supplies

  • Lining fabric
  • Fusible interfacing
  • 6 buttons
  • Shoulder pads

Cutter's Must

From main fabric:

  • 1. Back (center) – 2 pieces
  • 2. Back (side) – 2 pieces
  • 3. Front (center) – 2 pieces
  • 4. Front (side) – 2 pieces
  • 5. Front yoke — 2 pieces
  • 6. Stand collar – 2 pieces
  • 7. Back neck facing – 1 piece
  • 8. Front facing – 2 pieces
  • 5. Sleeve (upper) – 2 pieces
  • 6. Sleeve (lower) – 2 pieces

From lining fabric:

  • 1. Back (center) – 2 pieces
  • 2. Front (center) – 2 pieces
  • 3. Back (side) – 2 pieces
  • 4. Front (side) – 2 pieces
  • 5. Front yoke — 2 pieces
  • 5. Sleeve (upper) – 2 pieces
  • 6. Sleeve (lower) – 2 pieces
  • 7. Pocket Bag — 4 pieces

From fusible interfacing:

  • 1. Front (center) — 2 pieces
  • 2. Front facing — 2 pieces
  • 3. Back neck facing — 1 piece
  • Also interface the armhole areas on the back, pocket opening, and hem of the garment.

Sewing Instructions

  1. Interface the pattern pieces with fusible interfacing.
  2. On the back, stitch the darts. Press the dart allowances towards the center. Topstitch along the dart 0.5 cm from the seam. On the back, stitch the princess seams. Press seam allowances open. Stitch the center back seam. Press seam allowance open.
  3. Attach the pocket bag to the center front and side front respectively. On the front, stitch the princess seams, simultaneously stitching the pocket bag. Press seam allowances open, clipping the corner on the side front. Press the pocket towards the center.
  4. Attach the front yoke. Press the seam allowance towards the yoke. Topstitch 1 cm from the seam.
  5. Stitch the shoulder and side seams of the coat. Clip and press seam allowances open.
  6. Stitch the elbow seam of the sleeve. Press seam allowance open. Stitch the front sleeve seam. Press seam allowance open. Set the sleeve into the armhole. Press the upper of the sleeve cap towards the neckline. Topstitch along the sleeve cap, 5 cm from the shoulder seam. Attach shoulder pads.
  7. Stitch the shoulder seams of the front facings and facing. Press seam allowances open.
  8. Attach the outer collar stand to the coat neckline, and the inner collar stand to the neckline of the front facings and facing. Clip seam allowances at curves, press seam allowances open.
  9. Press up the hem allowance. Place the front facing on the right side of the front, right side down. Attach the lower edge of the front facing to the hem allowance. Press seam allowances upwards. Pin the front facing and the upper of the garment and stitch along the front edge and the collar stand. Attach the lower edge of the front facing to the front strictly along the marked hemline, stopping 1.5 cm before the inner edge of the front facing. Trim seam allowances at collar stand corners, turn right side out, and smooth out the seams.
  10. On the lining fabric pieces, stitch the seams, leaving an opening in the left side seam for turning. Set in the sleeves. Attach the lining to the front facings and facing.
  11. Attach the lining to the hem of the garment. Turn the coat right side out through the opening. Close the opening.
  12. Topstitch along the front edge and the upper edge of the collar stand. Fold back the side of the pocket, and topstitch along the pocket opening line.
  13. Make buttonholes and sew on buttons.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?