Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4524
#4526

Paneled Three-Quarter Sleeve Shift Dress

Pattern #4525

A women's straight shift dress ending above the knee, built from panels: princess seams, a yoke across the front and back, and a separate band at the hem. Three-quarter set-in sleeves and an invisible zipper in the centre back seam. Drafted to your own measurements. Recommended fabric: dress fabrics made from natural or blended fibres.

Tech. Description

Paneled Three-Quarter Sleeve Shift Dress

A women's straight shift dress ending above the knee, built from panels: princess seams, a yoke across the front and back, and a separate band at the hem. Three-quarter set-in sleeves and an invisible zipper in the centre back seam.

When To Wear

  • At the office in spring and autumn, with tights and closed shoes or under a jacket.
  • For daytime outings with a cardigan or a light coat.

Key Design Features

Silhouette: Straight, close to the body, shaped by princess seams on the front and back.

Length: Above the knee.

Neckline: Round, finished with an interfaced facing that is secured to the shoulder seams and the zipper tape.

Sleeves: Three-quarter length, one-piece set-in sleeves with a single underarm seam.

Front: A centre front panel between two side front panels, a yoke above the bust and a horizontal band at the hem.

Back: The same layout as the front: centre back in two halves, side back panels, a yoke and a hem band.

Closure: Invisible zipper in the centre back seam.

Finishing: Seams overlocked and pressed towards the centre, yokes and hem band; dress and sleeve hems turned up and topstitched.

Level Of Difficulty

Intermediate. Matching the yoke and hem band seams to the princess seams, an invisible zipper, a faced neckline and set-in sleeves.

Fabric Recommendations

Dress fabrics made from natural or blended fibres.

Additional Supplies

  • Fusible interfacing (neckline facings)
  • Invisible zipper

Cutter's Must

If the patterns have a double contour, seam allowances are included. If the contour is single, seam allowances are not included. Seam allowances: hem allowance for the garment bottom and sleeve hem – 2.0 cm, other seams 1 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need. When stitching pieces, pay attention to the notches - they must match!

From main fabric:

  • Center Back – 2 pieces
  • Side Back – 2 pieces
  • Back Yoke – 2 pieces
  • Back Placket (hem band) – 1 piece
  • Center Front – 1 piece
  • Side Front – 2 pieces
  • Front Yoke – 1 piece
  • Front Placket (hem band) – 1 piece
  • Sleeve – 2 pieces
  • Back Neckline Facing – 2 pieces
  • Front Neckline Facing – 1 piece

From fusible interfacing:

  • Back Neckline Facing – 2 pieces
  • Front Neckline Facing – 1 piece

Sewing Instructions

  1. Fuse interfacing to the Back Neckline Facings and the Front Neckline Facing.
  2. Stitch the back princess seams (Center Back to Side Back), press the seam allowances towards the centre and serge. Stitch the Back Yokes to the back, press the seam allowances towards the yokes and serge.
  3. Serge the centre back edges separately. Stitch the centre back seam from the zipper mark to the lower edge. Press the seam allowances open, pressing the zipper opening allowances as well. Insert the invisible zipper.
  4. Stitch the Back Placket (hem band) to the lower edge of the back, press the seam allowances upwards and serge.
  5. Stitch the front princess seams (Center Front to Side Front), press the seam allowances towards the centre and serge. Stitch the Front Yoke to the front, press the seam allowances towards the yoke and serge. Stitch the Front Placket (hem band) to the lower edge of the front, press the seam allowances upwards and serge.
  6. Stitch the shoulder and side seams, press the seam allowances towards the back and serge.
  7. Stitch the shoulder seams of the facings and press the seam allowances open. Serge the outer edge. Place the facing on the dress, right sides together, matching the neckline edges. Stitch around the neckline. Clip the seam allowances on the curves and trim them at the corners; along the front neckline, trim the allowance to 0.1–0.2 cm. Turn the facing to the inside, ease out the edges and press. Tack the facing to the shoulder seams and the zipper tape.
  8. Stitch the sleeve seam, press the seam allowances towards the back and serge. Set the sleeves into the armholes, matching the notches. Press the seam allowances and serge.
  9. Serge the lower edges of the dress and sleeves. Press the hem allowances to the wrong side and topstitch.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?