Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4498
#4500

Tunic with Stand Collar

Pattern #4499

A women's woven tunic-blouse with a band (stand) collar and a split V-neck edged with narrow plackets, a back yoke with a centre back seam, and roll-up sleeves held by a button tab. Drafted to your own measurements. Recommended fabric: blouse fabrics in natural or blended fibres; shirting fabrics.

Tech. Description

Tunic with Stand Collar

A women's woven tunic-blouse with a band (stand) collar and a split V-neck edged with narrow plackets, a back yoke with a centre back seam, and roll-up sleeves held by a button tab.

When To Wear

  • In spring and summer with jeans, trousers or a straight skirt.
  • For casual office days, worn loose over slim trousers.

Key Design Features

Silhouette: Straight, loose fit; the front is shaped with darts.

Length: Mid-thigh length, with a curved hem.

Collar: Stand collar in two pieces (outer stand interfaced), ending at the edges of the V opening.

Front: One piece with a V-shaped slit at the centre front, finished with two folded, interfaced plackets; no buttons.

Sleeves: Set-in sleeves, sewn in one seam with the side seam. A tab with a buttonhole is stitched to the inside of the sleeve and buttons on the outside to hold the sleeve rolled up.

Back: Back yoke and centre back seam.

Finishing: Body hem turned up 1.5 cm and topstitched; sleeve hems double-turned 1 cm and topstitched.

Level Of Difficulty

Intermediate. Placket edges on a V slit with clipped corners, a stand collar and sleeve tabs with buttonholes.

Fabric Recommendations

Blouse fabrics in natural or blended fibres; shirting fabrics.

Additional Supplies

  • Fusible interfacing (plackets, outer collar stand)
  • 2 buttons

Cutter's Must

From main fabric:

  • 1. Back Yoke – 1 piece
  • 2. Back – 2 pieces
  • 3. Front - 1 piece
  • 4. Placket – 2 pieces
  • 5. Sleeve - 2 pieces
  • 6. Collar Stand – 2 pieces
  • 7. Sleeve Tab – 2 pieces
  • From fusible interfacing: placket, outer collar stand.

Sewing Instructions

  1. Fuse the plackets and outer collar stand with fusible interfacing.
  2. Stitch the center back seam, press seam allowances to the left and serge. Attach the yoke to the back, press seam allowances upwards and serge.
  3. Stitch the darts on the front, press depths upwards.
  4. Press the plackets in half lengthwise, right side out. Attach the plackets to the front along the long edge, stopping 1 cm from the bottom. Clip the front 's seam allowance at the corners, stopping 1 mm from the stitching. Turn the ends of the plackets inwards and stitch, securing the bottom edge. Serge the seam allowances.
  5. Stitch the shoulder seams of the blouse, press seam allowances towards the back and serge.
  6. Fold the collar stand pieces right sides together and stitch along the outer edge, starting and ending the stitching precisely at the collar attachment line. Turn the collar stand right side out, press.
  7. Attach the outer collar stand to the neckline, turn under the raw edge of the inner collar stand and topstitch into the attachment seam.
  8. Fold the tab right sides together and stitch the long and short sides. Trim seam allowances at the corners, turn right side out and press. Serge the buttonhole. Attach the tab to the wrong side of the sleeve according to markings. Sew a button to this spot on the right side.
  9. Set the sleeves into the open armholes. Serge the seam allowances. Stitch the sleeve seams in one continuous seam with the side seam. Press seam allowances towards the back and serge.
  10. Serge the bottom edge of the garment, press to the wrong side and topstitch. Press the sleeve hem twice by 1 cm and topstitch.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?