Coat with Wrap-Over Collar and Asymmetric Closure
A women's knee-length coat with a straight cut, a large two-piece collar that wraps over to one side and an off-centre five-button closure. It has single-welt pockets, a back vent, a tie belt and a full lining.
When To Wear
- In autumn and spring, over dresses, skirts or trousers.
- Buttoned and tied at the waist, or without the belt as a straight coat.
Key Design Features
Silhouette: Straight, with front waist darts; drawn in by the belt.
Length: Knee length.
Collar: Wide two-piece collar that wraps across the front; the under collar is set into the coat neckline, the upper collar into the facing.
Closure: Asymmetric, five buttons with buttonholes on the right front.
Sleeves: Long one-seam set-in sleeves; a separate wing piece is sewn to the front and back along the armhole; shoulder pads.
Pockets: Single-welt pockets on the fronts with lining pocket bags.
Back: Centre back seam with an interfaced vent.
Waist: Self-fabric tie belt, topstitched 0.5 cm from the edge.
Finishing: Hem allowance 3.5 cm, sleeve hem 3 cm.
Lining: Full lining with lined sleeves, attached to the facings, back neck facing, sleeve hems and coat hem, and cut open around the vent.
Level Of Difficulty
Intermediate. Welt pockets, a lined back vent, a collar set between coat and facing, and a full bagged lining.
Fabric Recommendations
Coating fabrics from natural or blended fibres.
Additional Supplies
- Lining fabric
- Fusible interfacing (facings, welts, back neck facing, upper collar, armhole edges, wing pieces, pocket area, vent)
- 5 buttons
- Shoulder pads
Cutter's Must
From main fabric:
- Front – 2 pieces
- Back – 2 pieces
- Sleeve – 2 pieces
- Facing – 2 pieces
- Welt – 2 pieces
- Back neck facing – 1 piece
- Collar – 2 pieces
- Belt – 1 piece
- Wing – 2 pieces
From lining fabric:
- Front – 2 pieces
- Back – 2 pieces
- Sleeve lining – 2 pieces
- Small pocket bag – 2 pieces
- Large pocket bag – 2 pieces
- From fusible interfacing: facing, welt, back neck facing, upper collar.
The back cutting pieces are cut according to the upper patterns, minus the width of the neck facing and plus the wing.
Sewing Instructions
- Fuse fusible interfacing to the facing, back neck facing, upper collar, armhole edge on the front and back, and wing. Fuse the pocket placement area on the front.
- On the wrong side of the back pieces, fuse the vent. On the right side, mark the center seam line (vent fold line). Press the left back along the vent fold line. Align the pieces along the center seam. Stitch the center edge of the back and the vent corner, stopping 1 cm from the vertical vent edge. Clip the vent seam allowance corner on the right. Press open the center seam allowances, press the vent seam allowances, and secure them on the right side with machine stitching.
- Stitch and press the darts on the front. Press the dart fullness downwards.
- Mark the pocket placement. Press the welt in half lengthwise, wrong side in. Stitch the small pocket bag to the inner side of the welt. Attach the welt to the front along the lower pocket marking line. Attach the large pocket bag to the front along the upper pocket marking line. The ends of the stitches should finish at the short marking lines. Cut the pocket opening. Make diagonal cuts 1-1.5 cm from the end of the pocket. Turn the welt and large pocket bag to the wrong side through the opening. Secure the pocket ends from the wrong side with a double backstitch at the base of the corners. Stitch the pocket bag edges.
- Stitch and press open the shoulder and side edges. Attach the wing to the back and front. Press the seam allowance towards the wing.
- Stitch the shoulder edges of the back neck facing and facing. Press the seams open.
- Place the facing and facing right side down onto the right side of the coat and stitch the fronts with the FACINGs.
- Fold the collar pieces right sides together. Stitch the outer edge and ends of the collar. Turn the collar out and press. Attach the lower collar to the neckline of the back and front.
- Attach the upper collar to the neckline of the facing and facing. Press the seam open. Secure the collar attachment seam allowances close to the seams.
- Stitch the sleeve seam. Press the seam allowance open. Attach the sleeves into the armhole according to the notches. Attach the shoulder pads.
- Serge and press the hem seam allowance of the garment.
- On the lining fabric cutting pieces, stitch the seams and attach the sleeves.
- Attach the lining to the inner edges of the FACINGs and the back neck facing. Attach the lining to the bottom of the sleeve. Near the vent, cut the lining and secure it to the vent edges. Attach the lining to the bottom of the garment.
- Fold the belt in half lengthwise, right sides together, and stitch, leaving an opening. Turn the belt through the opening and sew it closed. Topstitch along the contour 0.5 cm from the edge.
- On the right front, make buttonholes. Sew on buttons accordingly.