Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4474
#4476

Tailored Collarless Shaped Jacket

Pattern #4475

A hip-length women's jacket with a round collarless neckline, edge-to-edge fronts with a hidden fastening, princess seams and a horizontal waist seam. Two-piece sleeves with a vent at the hem; fully lined. Drafted to your own measurements. Recommended fabric: suiting fabrics of natural or blended fibres.

Tech. Description

Tailored Collarless Shaped Jacket

A hip-length women's jacket with a round collarless neckline, edge-to-edge fronts with a hidden fastening, princess seams and a horizontal waist seam. Two-piece sleeves with a vent at the hem; fully lined.

When To Wear

  • At the office in spring and autumn, over blouses and fine knit tops.
  • With a matching skirt or trousers as a suit.
  • Over a sheath dress for daytime events.

Key Design Features

Silhouette: Fitted through the waist by princess seams and a waist seam; the lower part sits over the hips.

Length: Hip length.

Neckline: Round and collarless, with a short dart at the neckline of each centre front and centre back panel. The back neckline is stabilised with fusible tape.

Sleeves: Two-piece set-in sleeves with an interfaced vent at the hem.

Closure: The front edges meet at the centre front; a hidden fastening is set into the front edge seam between the jacket and the lining.

Pockets: Two lined, interfaced flaps on the lower fronts, set just below the waist seam, without pocket openings.

Back: Centre back seam, princess seams and a separate lower part joined at the waist seam.

Finishing: Interfaced front facings, back neck facing and flaps; thin shoulder pads.

Lining: Full lining cut from the main pieces less the facings, sewn to the front edges, neckline, hem and sleeve hems, and tacked to the jacket along the waist seam.

Level Of Difficulty

Intermediate. Matching princess seams to a waist seam, two-piece sleeves with vents, a bagged lining and a hidden fastening set into the front edge.

Fabric Recommendations

Suiting fabrics of natural or blended fibres.

Additional Supplies

  • Lining fabric
  • Fusible interfacing (front facings, back neck facing, flaps, sleeve vents)
  • Fusible stay tape for the back neckline
  • Thin shoulder pads
  • Hidden fastening for the front

Cutter's Must

From main fabric:

  • Back (center) – 2 pieces
  • Back (side) – 2 pieces
  • Front (side) – 2 pieces
  • Front (center) – 2 pieces
  • Front Facing – 2 pieces
  • Back Neck facing – 1 piece
  • Sleeve (upper) – 2 pieces
  • Sleeve (lower) – 2 pieces
  • Back (lower) — 1 piece
  • Front (lower) — 2 pieces
  • Flap — 2 pieces
  • Lining pieces are cut according to the main fabric pieces, subtracting the width of the back neck facing and front facing.

From lining fabric:

  • Back (center) – 2 pieces
  • Back (side) – 2 pieces
  • Front (side) – 2 pieces
  • Front lining – 2 pieces
  • Sleeve (upper) – 2 pieces
  • Sleeve (lower) – 2 pieces
  • Back (lower) — 1 piece
  • Front (lower) — 2 pieces
  • Flap — 2 pieces
  • From fusible interfacing: front facing, back neck facing, flap.

Sewing Instructions

  1. Fuse fusible interfacing to the designated pieces. Along the back neckline, apply an additional fusible interfacing strip. Fuse the sleeve vent.
  2. Place the flap and lining right sides together and stitch along the outer contour. Trim seam allowances, turn right side out, and press. Position the flap on the lower front according to the mark and secure.
  3. Stitch the dart on the center front. Press the dart depth towards the center. Stitch the princess seam on the front. Press the seam allowance towards the center. Attach the lower. Press the seam allowance open.
  4. Stitch the dart on the center back. Press the dart depth towards the center. Stitch and press open the princess seams on the back. Stitch the center back seam. Press the seam allowance open. Attach the lower. Press the seam allowance open.
  5. Stitch the shoulder and side seams of the jacket. Press seam allowances open.
  6. Stitch the elbow seam of the sleeve and the vent corners on the lower and upper sleeve parts. Press open the sleeve elbow seam, clip the seam allowance at the corner, and press the vent. Press the sleeve hem. Stitch and press open the front sleeve seam.
  7. Set the sleeves into the armholes, matching notches, easing the sleeve cap in the upper. Attach shoulder pads.
  8. Stitch and press open the shoulder seams of the back neck facing and front facing. Stitch the lining pieces similarly to the main fabric pieces, leaving an opening in the left sleeve elbow seam. Attach the lining to the facing and front facing.
  9. Place the jacket and lining right sides together, inserting the closure, pin, aligning the outer edges. Stitch the lining along the front opening, neckline, and bottom of the jacket. Attach the lining to the sleeve hem. Turn the jacket right side out through the opening. Secure the lining to the main fabric at the waist seam. Close the technical opening.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?