Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4473
#4475

Fitted Asymmetrical Zipper Stand Collar Half Coat

Pattern #4474

A fitted, hip-length women's jacket with an asymmetric front closed by a separating zipper, a stand collar, princess seams and a horizontal waist seam on the front and back. Fully lined, with shoulder pads. Drafted to your own measurements. Recommended fabric: lightweight coating fabrics of natural or blended fibres.

Tech. Description

Fitted Asymmetrical Zipper Stand Collar Half Coat

A fitted, hip-length women's jacket with an asymmetric front closed by a separating zipper, a stand collar, princess seams and a horizontal waist seam on the front and back. Fully lined, with shoulder pads.

When To Wear

  • In spring and autumn over knitwear, with jeans or slim trousers.
  • Over dresses and skirts as a light outer layer.

Key Design Features

Silhouette: Fitted through the waist, shaped by princess seams above and below the waist seam.

Length: Hip length.

Collar: Stand collar of an outer and an inner layer, interfaced, continuing the line of the front edge.

Sleeves: Long two-piece set-in sleeves with elbow and front seams, eased into the armhole; shoulder pads and sleeve head rolls.

Closure: Off-centre separating zipper running from the collar stand to the hem; one half is set into a seam of the left front, the other into the right front edge.

Front: Right and left fronts cut differently, each with a horizontal waist seam and princess seams; interfaced left and right facings.

Back: Centre back seam, princess seams from the armholes and a horizontal waist seam.

Finishing: Front edge and stand topstitched 1 cm from the edge; hems turned up 3 cm and interfaced.

Lining: Full lining, cut minus the facings, bagged out through an opening in the right sleeve lining seam.

Level Of Difficulty

Advanced. Many shaped panels, an asymmetric zipper inserted into a seam and the faced front edge, a two-layer stand collar, eased two-piece sleeves and a bagged lining.

Fabric Recommendations

Lightweight coating fabrics of natural or blended fibres.

Additional Supplies

  • Lining fabric
  • Fusible interfacing (facings, back neck facing, collar stand, hem allowances)
  • Separating zipper
  • Shoulder pads
  • Sleeve head rolls

Cutter's Must

From main fabric:

  • Central upper back – 2 pieces
  • Middle upper back – 2 pieces
  • Side upper back – 2 pieces
  • Central lower back – 2 pieces
  • Side lower back – 2 pieces
  • Side upper front – 2 pieces
  • Middle upper front – 2 pieces
  • Central upper right front – 1 piece
  • Side lower front – 2 pieces
  • Central lower right front – 1 piece
  • Central left front – 1 piece
  • Middle lower front – 1 piece
  • Collar stand – 2 pieces
  • Left facing – 1 piece
  • Right facing – 1 piece
  • Back neckline facing – 1 piece
  • Upper sleeve – 2 pieces
  • Lower sleeve – 2 pieces

From lining fabric:

  • Central upper back – 2 pieces
  • Middle upper back – 2 pieces
  • Side upper back – 2 pieces
  • Central lower back – 2 pieces
  • Side lower back – 2 pieces
  • Side upper front – 2 pieces
  • Middle upper front – 2 pieces
  • Side lower front – 2 pieces
  • Central lower right front – 1 piece
  • Middle lower front – 1 piece
  • Upper sleeve – 2 pieces
  • Lower sleeve – 2 pieces

Attention: lining pieces for the back and front are cut with the width of the back neckline facing and front facing deducted, respectively.

From fusible interfacing:

  • Collar stand – 1 piece
  • Left facing – 1 piece
  • Right facing – 1 piece
  • Back neckline facing – 1 piece

Sewing Instructions

  1. Fuse the front facings, back neckline facing, collar stand, and hem seam allowances of the garment and sleeve with fusible interfacing. The fusible interfacing should extend 1 cm beyond the marked hemline.
  2. Stitch and press open the princess seams of the upper back. Stitch and press open the center seam of the upper back. Stitch and press open the princess seams of the lower back. Stitch and press open the center seam of the lower back. Stitch the upper and lower back sections together, press seam allowances open. Attach the outer collar stand to the neckline, press seam allowances open.
  3. Right front: Stitch and press open the princess seams of the upper front. Stitch the side and central lower front sections together, press seam allowances open. Stitch the upper and lower front sections together, press seam allowances open.
  4. Left front: Stitch the middle and side upper front sections together, press seam allowances open. Stitch the middle and side lower front sections together, press seam allowances open. Stitch the upper and lower front sections together, press seam allowances open. Stitch the central and side front sections together, inserting the left half of the zipper between the notches.
  5. Stitch the side and shoulder seams together with the collar stand seam, press seam allowances open.
  6. Attach the inner collar stand to the neckline facing, press seam allowances open. Stitch and press open the shoulder seams of the back neckline facing and front facings.
  7. Place the front facing on the right side of the front, right side down, pin and stitch along the front edge and collar stand seam, inserting the right half of the zipper. Trim seams at corners. Turn out the front edges and collar stand, straighten seams, press.
  8. Stitch and press open the elbow seam of the sleeve. Press up the sleeve hem. Stitch and press open the front seam of the sleeve.
  9. Set the sleeves into the armholes according to the notches, easing the sleeve cap. Insert shoulder pads and sleeve head rolls.
  10. On the lining pieces, stitch the seams and set in the sleeves, similar to the main fabric pieces, leaving an opening in the front right sleeve seam.
  11. Stitch the lining to the inner edges of the front facings and the back neckline facing. Secure the seam allowances of the collar stand attachment close to the seams. Stitch the lower edges of the front facings to the front. Trim seam allowances at corners. Turn the front edges to the right side, straighten seams. Press the lower edge of the garment to the wrong side. Stitch the lining to the bottom of the garment and to the sleeve hem. Turn the jacket through the opening in the sleeve. Close the opening.
  12. Topstitch along the front edge and collar stand 1 cm from the edge.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?