Tailored Collarless Coat with Mock Flap Pockets
A fully lined, collarless women's coat of about knee length with a round neckline, edge-to-edge fronts with a concealed fastener, two-piece set-in sleeves and sewn-on mock pocket flaps. The front is divided by a topstitched chest seam and a waist seam, the back by a seam above the waist.
When To Wear
- In spring and autumn over dresses, skirts and trousers.
- For the office, as a lightweight coat over a suit.
Key Design Features
Silhouette: Shaped at the waist with darts and horizontal seams, straight below the waist.
Length: About knee length.
Neckline: Round collarless neckline, finished with an interfaced back neck facing and the front facings.
Sleeves: Two-piece set-in sleeves (upper and under sleeve) with elbow and front seams; shoulder pads and sleeve heads.
Closure: Edge-to-edge fronts with a concealed fastener stitched into the front edge seam together with the facing.
Front: Each front is cut in three parts: upper, middle and lower. The seam across the chest is topstitched 0.5 cm from the seam; the middle and lower parts are joined at the waist and shaped with darts.
Pockets: No pocket openings: two-layer flaps, the upper layer interfaced, are stitched on along a placement line below the waist, turned down and secured with a line of stitching 0.5 cm from the seam.
Back: Upper and lower back with darts, joined by a horizontal seam above the waist; centre back seam.
Finishing: Coat and sleeve hems interfaced, turned up 3 cm and sewn by hand with blind stitches; facings tacked by hand to the shoulder and centre back seams.
Lining: Full lining, cut from the main pieces minus the front facings and back neck facing.
Level Of Difficulty
Intermediate. Two-piece sleeves with shoulder pads and sleeve heads, a lined coat with facings, a concealed fastener set into the front edge seam, and multi-part fronts matched at the seams.
Fabric Recommendations
Suiting fabrics made from natural or blended fibres.
Additional Supplies
- Lining fabric
- Concealed fastener
- Shoulder pads
- Sleeve heads
- Fusible interfacing (upper flaps, front facings, back neck facing, coat and sleeve hems)
Cutter's Must
From main fabric:
- Upper Back – 2 pieces
- Lower Back – 2 pieces
- Upper Front – 2 pieces
- Middle Front – 2 pieces
- Lower Front – 2 pieces
- Upper Sleeve – 2 pieces
- Lower Sleeve – 2 pieces
- Back Neckline Facing – 2 pieces
- Center Front Facing – 2 pieces
- Flap – 4 pieces
From lining fabric:
- Cut from the main pattern pieces, minus the Back Neckline Facing and Center Front Facing
From fusible interfacing:
- Flap – 2 pieces (upper flaps)
- Center Front Facing – 2 pieces
- Back Neckline Facing – 2 pieces
- Strips for the hem of the coat and the sleeve hems
Sewing Instructions
- Fuse interfacing to the upper Flap pieces, Center Front Facing, Back Neckline Facing and the hems of the coat and sleeves.
- On the back pieces, stitch the darts, press the dart depths towards the center. Stitch the Upper Back and Lower Back together, serge the seam allowances and press them downwards. Stitch the center back seam. Serge the seam allowances and press them open.
- On the front pieces, stitch the darts, press the dart depths towards the center. Stitch the Lower Front and Middle Front together. Serge the seam allowances and press them downwards. Stitch the Upper Front to the Middle Front. Serge the seam allowance and press it upwards. Topstitch 0.5 cm from the seam.
- Place the Flap pieces together in pairs, right sides facing, and stitch along three sides. Trim the seam allowances at the corners, turn right side out, and press. Serge the upper edge. Place the flap right side down along the placement line, with the raw edge towards the hem, and stitch. Turn the flap downwards and stitch a securing line 0.5 cm from the attachment seam.
- Stitch the shoulder and side seams, press the seam allowances open and serge.
- Stitch the elbow seam of the sleeve. Serge the seam allowance and press it open. Stitch the front seam of the sleeve. Serge the seam allowances and press them open. Serge the lower edge of the sleeve. Fold the seam allowance inwards and press. Set the sleeves into the armholes, matching the notches. Insert shoulder pads and sleeve heads.
- Stitch the shoulder seams of the Center Front Facings and Back Neckline Facing, press the seam allowances open. Serge the pieces along the outer edge.
- Place the facings on the coat right sides together, align the edges and pin. Stitch along the front edges and neckline, inserting the concealed fastener. Trim the seam allowances at the corners. Turn the facings to the wrong side and attach it to the shoulder and center seams by hand.
- Press the hems of the coat and sleeves to the wrong side and hem with blind stitches.