Collared Wrap Blouse with Side Waist Tie
A women's fitted wrap blouse with a shirt collar on a stand, three-quarter sleeves with deep cuffs and a tie at the left side of the waist. The wrapped fronts end in points at the hem and are held closed by snap tape.
When To Wear
- For the office, with straight trousers or a pencil skirt.
- In spring and autumn, worn alone or under a sleeveless dress or pinafore.
Key Design Features
Silhouette: Fitted, shaped with bust, waist and shoulder darts on the fronts and back.
Length: Hip length, with the front edges cut into points that hang below the back hem.
Collar: Shirt collar with a separate stand, both interfaced; the stand runs into the front edges, which are faced with interfaced facings.
Sleeves: Three-quarter, one-piece set-in sleeves finished with deep interfaced cuffs folded in half lengthwise, the cuff opening placed at a mark.
Front: Asymmetric wrap: the right front is folded into pleats near the side (pleat depths turned upwards) and wraps over the left front. Snap tape is topstitched to the fronts to close the wrap.
Waist: Two belt ties: one sewn into the left side seam, the other into the edge of the right front, tied at the left side.
Back: Centre back seam, with darts for shaping.
Finishing: Hem turned twice by 1 cm and topstitched.
Level Of Difficulty
Intermediate. Collar with a stand set into a faced neckline, darts and pleats, ties sewn into the seams, cuffs.
Fabric Recommendations
Blouse fabric in natural or blended fibres with added elastane.
Additional Supplies
- Fusible interfacing (facings, cuffs, upper collar, collar stand)
- Snap tape
Cutter's Must
From main fabric:
- Back - 2 pieces
- Left front - 1 piece
- Right front - 1 piece
- Left facing - 1 piece
- Right facing - 1 piece
- Belt - 2 pieces
- Sleeve – 2 pieces
- Cuff – 2 pieces
- Collar – 2 pieces
- Collar Stand – 2 pieces
From fusible interfacing:
- Collar – 1 piece
- Collar Stand – 1 piece
- Left facing - 1 piece
- Right facing - 1 piece
- Cuff – 2 pieces
Sewing Instructions
- Fuse fusible interfacing to the facings, cuffs, upper collar, and inner collar stand.
- Place the upper collar and lower collar right sides together. Stitch the ends and outer edge of the collar. Trim seam allowances. Turn the collar right side out, shape, and press. Place the collar stand pieces right sides together, insert the finished collar between them, align the notches, and stitch, simultaneously stitching the ends of the collar stand. Turn the finished collar right side out and press.
- Fold the belt pieces in half lengthwise, right sides together, and stitch along the long side and one short side. Trim seam allowances at corners, turn the belt right side out, shape, and press.
- Mark and stitch the bust darts, waist darts, and shoulder darts on the front and back. Press bust darts upwards, and waist and shoulder darts towards the center of the pieces. Fold and secure the pleats on the right front (depths directed upwards).
- Stitch the center back seam of the back. Overlock seam allowances and press towards the left side seam.
- Stitch the shoulder and side seams, inserting the belt piece into the left side seam. Overlock seam allowances and press towards the back.
- Overlock the shoulder seams and the inner edges of the facings. Baste the collar stand into the neckline. Place the facings right sides together with the garment, insert the right side of the belt, and stitch: the left front edge from the bottom to the shoulder seam, at the shoulder seam slash the inner collar stand and stitch only the outer collar stand into the neckline up to the right shoulder seam, at the shoulder seam slash the inner collar stand, fold back, and the right front edge to the bottom. Slash seam allowances at curves, trim at corners. Turn the facings to the wrong side, shape, and press. Fold the raw edge of the inner collar stand inwards and topstitch into the joining seam.
- Stitch and overlock the sleeve seams. Set the sleeves into the armholes, press, and overlock.
- Fold the cuffs in half lengthwise and stitch the short sides. Turn the cuffs right side out and press. Attach the cuff to the bottom of the sleeve, aligning the seam of the cuff side edges with the mark. Press and overlock seam allowances.
- Press the bottom edge of the garment to the wrong side by 1 cm, then by another 1 cm, and topstitch.
- Topstitch the snap tape onto the front panels.