Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4288
#4290

Three Quarter Sleeve Draped Front Jersey Top

Pattern #4289

A women's top for medium-stretch knit fabric with a crossover front: two upper front pieces, gathered at the neckline, overlap on a darted inner front above an under-bust seam. Three-quarter sleeves and a centre back neck slit closed with one button and a thread loop. Drafted to your own measurements. Recommended fabric: medium-stretch knit fabric of natural or blended fibres.

Tech. Description

Three Quarter Sleeve Draped Front Jersey Top

A women's top for medium-stretch knit fabric with a crossover front: two upper front pieces, gathered at the neckline, overlap on a darted inner front above an under-bust seam. Three-quarter sleeves and a centre back neck slit closed with one button and a thread loop.

When To Wear

  • For the office with trousers or a straight skirt.
  • In spring and autumn on its own, or under a jacket in winter.

Key Design Features

Silhouette: Close-fitting, with a seam under the bust.

Length: Hip length.

Neckline: Round neck finished with a folded 4 cm knit binding, topstitched on the right side.

Sleeves: Three-quarter set-in sleeves, sewn into the open armhole; sleeve and side seams are stitched in one pass.

Front: Inner front with darts; two upper front pieces with turned and topstitched bias edges, gathered along the neckline and laid crosswise over the inner front; lower front in one piece below the under-bust seam.

Back: Two pieces with a centre back seam; the seam is left open at the top as a slit, its edges topstitched 0.1 cm.

Closure: One button on the right side of the slit, a thread loop on the left.

Finishing: Knit seams stretch-stitched or overlocked; hems topstitched with a twin needle.

Level Of Difficulty

Intermediate. Layered, gathered front pieces matched at notches, a binding stretched onto the neckline, and a back slit with a thread loop.

Fabric Recommendations

Medium-stretch knit fabric of natural or blended fibres.

Additional Supplies

  • 1 button

Cutter's Must

If the patterns have a double contour, they include seam allowances. If the contour is single, the patterns do not include seam allowances. Seam allowances: Hem allowance for the garment bottom, sleeve hem and along the bias edge of the Upper Front – 1.5 cm, other seams 0.8 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need.

  • Back – 2 pieces
  • Inner Front – 1 piece
  • Upper Front – 2 pieces
  • Lower Front – 1 piece
  • Sleeve – 2 pieces
  • Strip for the neckline binding – 4 cm wide, length equal to the neckline + 5 cm (cut by measurement)

Tip: Cut pieces from knit fabrics are stitched with a special elastic or narrow zigzag stitch. The hem allowance is topstitched with a twin needle to maintain elasticity.

Sewing Instructions

When stitching pieces, pay attention to the notches - they must match!

  1. Overlock the centre back edge of the right Back from the neckline to 2-3 cm below the slit mark. Press this allowance to the wrong side. Place the Back pieces right sides together, aligning the centre back edges from the hem up to the slit marks. Fold the overlocked section of the right Back out of the way. Overlock the upper section of the centre back edge of the left Back, stitching and overlocking the centre back seam below the slit in the same pass.
  2. Stitch the darts on the Inner Front. Trim the dart depths with the overlocker. Overlock the armhole edge from the mark up to the neckline.
  3. Overlock the bias edge of each Upper Front, fold it to the wrong side and topstitch. Along the neckline edges of the Upper Front pieces, stitch with a loosened upper thread and gather. Lay the Upper Front pieces over the Inner Front, overlapping them as shown on the drawing. Baste the pieces together, matching the notches.
  4. Stitch the Upper Front unit to the Lower Front. Overlock the seam and press downwards.
  5. Stitch the shoulder seams. Overlock the seam and press towards the back.
  6. Set the sleeves into the open armholes, matching the notches. Overlock the seams and press.
  7. Stitch the side seams, continuing into the sleeve seam in one pass. Overlock the seam allowances.
  8. Cut a strip 4 cm wide, with a length equal to the neckline + 5 cm. Fold the strip in half lengthwise, right side out, and press. Place the strip on the wrong side of the neckline and stitch. Turn to the right side and topstitch, slightly stretching the fold of the strip. Trim the ends of the strip. Place a bar tack on the neckline at the centre back seam.
  9. Topstitch the centre back seam allowances along the slit at 0.1 cm.
  10. Overlock the bottom edge of the garment and the sleeve hems. Fold to the wrong side, press and topstitch.
  11. Make a thread loop. Sew the loop to the left side of the slit. Sew the button on the right side.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?