Stand Collar Peplum Jacket

Name: Stand Collar Peplum Jacket
Brand: Minerva Patterns
SKU: 2671
Price: 5.00 EUR
Availability: InStock

Pattern #2671

A women's fully lined jacket with a stand collar, a six-button front and a short gathered peplum joined to the bodice at the waist on both front and back. Decorative braid is stitched along the centre front. Drafted to your own measurements. Recommended fabric: suiting fabrics of natural or blended fibres.

Tech. Description

Stand Collar Peplum Jacket

When To Wear

To the office over a blouse or fine knit, with trousers or a straight skirt.
In spring and autumn as a light outer layer over a dress.

Key Design Features

Silhouette: Fitted bodice shaped with darts on the front and back, with a gathered peplum below the waist.

Length: To the high hip.

Collar: Stand collar with rounded upper corners, open at the centre front.

Sleeves: Long one-piece set-in sleeves with shoulder pads.

Closure: Single-breasted, six buttons on the bodice; front facings edge-stitched 0.2 cm from the seam.

Front: Upper and lower fronts joined by a waist seam; decorative braid along the centre front line.

Back: Centre back seam and darts on the upper back; the lower back is cut in one piece on the fold and gathered into the waist seam.

Lining: Full lining cut from the main pieces minus the facings, sewn to the hem of the jacket and sleeves; turned through an opening in the left sleeve seam.

Level Of Difficulty

Intermediate. Darts, gathered waist seams, a stand collar, front and back neck facings, set-in sleeves with shoulder pads and a bagged full lining.

Fabric Recommendations

Suiting fabrics of natural or blended fibres.

Additional Supplies

Lining fabric
Fusible interfacing (front facings, back neck facing, stand collar)
Shoulder pads
6 buttons
Decorative braid (approximate length marked on the front pattern piece)

Cutter's Must

If the patterns have a double contour, seam allowances are included. If the contour is single, seam allowances are not included. Seam allowances: all seams 1 cm. Hem allowance for jacket bottom and sleeve bottom - 3 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need (do not forget to account for paired and symmetrical pieces). When stitching pieces, pay attention to the notches - they must match!

From main fabric:
- Upper back – 2 pieces
- Lower back – 1 piece on fold
- Upper front – 2 pieces
- Lower front – 2 pieces
- Sleeve – 2 pieces
- Collar stand – 2 pieces
- Back neckline facing – 1 piece
- Front facing – 2 pieces
From lining fabric:
- Upper back – 2 pieces
- Lower back – 1 piece on fold
- Upper front – 2 pieces
- Lower front – 2 pieces
- Sleeve – 2 pieces
From fusible interfacing:
- Front facing – 2 pieces
- Back neckline facing – 1 piece
- Collar stand – 1 piece

Attention! Back and front pieces from lining fabric are cut according to the main fabric pieces, minus the back and front neckline facings, respectively.

Sewing Instructions

Fuse interfacing to the designated pieces.
Stitch darts on back pieces, trim dart depths and press towards the center. Stitch the center back seam. Press seam allowances open.
Along the upper edge of the lower back, stitch with a loosened upper thread and gather. Stitch the upper and lower back parts together. Press seam allowance upwards.
Stitch darts on front pieces, trim dart depths and press towards the center. Mark button placement on the left front edge. Topstitch decorative braid along the center line.
Along the upper edge of the lower front, stitch with a loosened upper thread and gather. Stitch the upper and lower front parts together. Press seam allowance upwards.
Stitch shoulder and side seams, press seam allowances open.
Fold collar stand pieces right sides together and stitch along the upper edge. Clip seam allowances at curves, turn collar stand right side out, straighten, and press. Attach collar stand to the neckline.
Stitch and press open shoulder seams of back neckline facing and front facings. Place front facings with facing right side down onto the right side of the front, pin, and stitch the front edge, neckline, and lower corner of the front edge. Trim seams at corners. Topstitch the seam allowance of the front edge facing to the front facing. Position the stitching 0.2 cm from the seam. Turn front edges right side out, straighten seams. Press the bottom of the garment.
Stitch sleeve seam, press seam allowances open. Set sleeves into armholes according to notches, press seam allowances. Attach shoulder pads.
Stitch lining pieces similarly to main fabric pieces, leaving an opening in the left sleeve seam. Attach lining to facing and front facings, press seam allowances towards the front facing. Attach lining to the bottom of the garment and sleeve bottom. Turn jacket right side out. Stitch the technical opening closed.
Buttonholes on the right front, sew buttons on the left front.