Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4529
#4531

Lined Tailored Jacket With Zipper Pockets

Pattern #4530

A women's fitted, hip-length lined jacket with an asymmetric front closed by a separating zipper set into the left princess seam, a high stand collar cut in one with the body, and two slanted zip pockets. Drafted to your own measurements. Recommended fabric: lightweight suiting made from natural or blended fibres.

Tech. Description

Lined Tailored Jacket With Zipper Pockets

A women's fitted, hip-length lined jacket with an asymmetric front closed by a separating zipper set into the left princess seam, a high stand collar cut in one with the body, and two slanted zip pockets.

When To Wear

  • In spring and autumn as a light outer layer over tops and knitwear.
  • With trousers, jeans or a fitted skirt for work and everyday wear.

Key Design Features

Silhouette: Fitted, shaped by princess seams on the front and back and a centre back seam.

Length: Hip length, with a rounded lower edge at the front.

Collar: High stand collar cut in one with the fronts and back, finished by the front facings and the back neck facing.

Closure: Asymmetric. The separating zipper runs diagonally from the collar to the hem: one half is sewn into the left front princess seam, the other into the right front edge between the front and its facing.

Pockets: Two slanted zip pockets on the lower front. The zipper is set under the cut opening with the teeth showing; lining pocket bags.

Sleeves: Two-piece set-in sleeves with elbow and front seams, an eased cap, shoulder pads and sleeve heads.

Back: Centre back seam and princess seams.

Lining: Full lining attached to the front facings, the back neck facing and a lower front facing, and the sleeve hems; bagged through an opening in the sleeve lining.

Level Of Difficulty

Advanced. Zip pockets cut into the front, a separating zipper in a diagonal princess seam, two-piece sleeves with pads and sleeve heads, and a bagged lining.

Fabric Recommendations

Lightweight suiting made from natural or blended fibres.

Additional Supplies

  • Lining fabric
  • Fusible interfacing (centre fronts, front facings, back neck facing, lower front facings, sleeve hems)
  • Separating zipper
  • 2 zippers for the pockets
  • Shoulder pads
  • Sleeve heads

Cutter's Must

If the patterns have a double contour, seam allowances are included. If the contour is single, the patterns are without seam allowances. Seam allowances: all seams 1 cm. Hem allowance for sleeve bottom 3 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need (do not forget to account for paired and symmetrical details). When stitching pieces, pay attention to the notches - they must match! Attention: Lining back pieces are cut according to the main fabric patterns, subtracting the width of the back neckline facing.

From main fabric:

  • Center back – 2 pieces
  • Side back – 2 pieces
  • Center front – 2 pieces
  • Side front – 2 pieces
  • Upper sleeve – 2 pieces
  • Lower sleeve – 2 pieces
  • Back neckline facing – 1 piece
  • Front facing – 2 pieces
  • Lower facing – 2 pieces

From lining fabric:

  • Center back – 2 pieces
  • Side back – 2 pieces
  • Side front – 2 pieces
  • Upper sleeve – 2 pieces
  • Lower sleeve – 2 pieces
  • Small pocket bag – 2 pieces
  • Large pocket bag – 2 pieces
  • From fusible interfacing: center front, front facing, back neckline facing, lower front facing, sleeve hem.

Sewing Instructions

  1. Fuse interfacing to the designated pieces.
  2. On the back, stitch the princess seams. Press seam allowances towards the center. Stitch the center back seam. Press seam allowance open.
  3. Mark the pocket placement on the front. Refine the pocket opening line. Cut the pocket opening. At a distance of 1-1.5 cm from the end of the pocket, make diagonal cuts. Turn the pocket allowances to the wrong side through the opening, straighten the edges. Adjust the end of the pocket from the wrong side. Place the zipper under the edges of the pocket opening so that the teeth are visible. Stitch the zipper. Stitch the lining right side to the wrong side of the zipper tape. Stitch the edges of the lining.
  4. On the left front, stitch the princess seam, inserting the left of the zipper tape. Press seam allowances open. Stitch the right princess seam. Press seam allowances open.
  5. Stitch and press open the side and shoulder seams of the jacket.
  6. Stitch and press open the elbow seam of the sleeve. Press up the sleeve hem. Stitch and press open the front seam of the sleeve. Set the sleeves into the armholes, matching notches and easing the sleeve cap. Insert shoulder pads, attach sleeve heads.
  7. On the lining pieces, stitch the seams and set the sleeves, leaving an opening in the front right sleeve seam. Stitch the shoulder seams of the front facings and neckline facing. Press seam allowances open. Stitch the lower facing to the front facing. Stitch the center seam of the lower facing, press seam allowance open. Stitch the lining to the front facings and neckline facing.
  8. Place the front facing right side down onto the right side of the front, pin and stitch along the front edge and neckline. Stitch the right front edge, inserting the right of the separating zipper tape. Trim seam allowances at corners. Turn the front edges to the right side, straighten the seams. Stitch the lining to the sleeve hem. Turn the jacket right side out through the opening. Close the opening.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?