Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4465
#4467

Jacket with Shawl Collar

Pattern #4466

A fitted, hip-length women's jacket for dense knit fabric, with a shawl collar cut in one with the fronts, front and back princess seams and a two-button front. All outer edges are bound with contrasting knit binding instead of hemmed. Drafted to your own measurements. Recommended fabric: dense knit fabrics of natural or blended fibres.

Tech. Description

Jacket with Shawl Collar

A fitted, hip-length women's jacket for dense knit fabric, with a shawl collar cut in one with the fronts, front and back princess seams and a two-button front. All outer edges are bound with contrasting knit binding instead of hemmed.

When To Wear

  • In spring and autumn over a top or fine knit, with trousers or a straight skirt.
  • For the office or everyday wear, as a soft alternative to a woven blazer.

Key Design Features

Silhouette: Fitted, shaped by princess seams on the front and back.

Length: Hip length, with rounded front corners at the hem.

Collar: Shawl collar cut in one with the centre front pieces and joined by a seam at the centre back; the collar on the facing is built the same way.

Sleeves: Long, two-piece set-in sleeves (upper and lower sleeve), cap eased into the armhole, lower edge bound.

Closure: Single-breasted, two buttons with buttonholes on the right front.

Pockets: Two patch pockets with rounded lower corners, topstitched onto the fronts, upper edge bound.

Back: Centre back seam, princess seams and a dart on each centre back piece.

Finishing: Front edges, collar and hem bound with contrasting knit binding through the jacket and facing together (no seam allowance on these edges); fusible stay tape along the back neckline; thin shoulder pads.

Lining: Unlined; the fronts and back neckline are finished with interfaced facings.

Level Of Difficulty

Intermediate. Princess seams, a two-piece set-in sleeve, a shawl collar set into the back neckline with clipped corners, and continuous binding of curved edges in knit fabric.

Fabric Recommendations

Dense knit fabrics of natural or blended fibres.

Additional Supplies

  • Knit fusible interfacing (front facings, back neckline facing)
  • Fusible stay tape for the back neckline
  • Thin shoulder pads
  • 2 buttons
  • Contrasting knit binding (approximate length is marked on the upper sleeve pattern piece)

Cutter's Must

From main fabric:

  • Center Back – 2 pieces
  • Side Back – 2 pieces
  • Side Front – 2 pieces
  • Center Front – 2 pieces
  • Center Front Facing – 2 pieces
  • Back Neckline Facing – 1 piece
  • Upper Sleeve – 2 pieces
  • Lower Sleeve – 2 pieces
  • Pocket – 2 pieces

From knit fusible interfacing:

  • Center Front Facing – 2 pieces
  • Back Neckline Facing – 1 piece

Sewing Instructions

  1. Fuse interfacing to the Center Front Facing and Back Neckline Facing. Apply an additional fusible stay tape along the back neckline.
  2. Stitch the princess seam on the front (Center Front to Side Front). Overlock the seam allowances and press towards the center. Bind the upper edge of the Pocket with the binding. Mark the pocket placement and topstitch the Pocket onto the front.
  3. Stitch the dart on the Center Back. Stitch the back princess seams (Center Back to Side Back), press open and overlock. Stitch and overlock the center back seam. Press the seam allowances to the left. Stitch the center back seam of the collar and press the seam allowances open. Stitch the shoulder and side seams of the jacket and press open. Clip the shoulder seam allowance of the front at the corner and stitch the collar into the back neckline. Press the seam allowances open.
  4. Stitch the shoulder seams of the Back Neckline Facing and Center Front Facing and press open. Stitch the center back seam of the collar on the Center Front Facing and press open. Clip the corner on the Center Front Facing and stitch the collar part into the neckline of the Back Neckline Facing. Press the seam allowances open. Overlock the outer (free) edges of the facings.
  5. Place the jacket and the facings wrong sides together and pin, matching the outer edges. Bind the front edges, collar and lower edge of the jacket with the binding.
  6. Stitch the elbow seam of the sleeve (Upper Sleeve to Lower Sleeve). Overlock the seam allowances and press towards the Upper Sleeve. Stitch the front sleeve seam. Overlock the seam allowances and press towards the Upper Sleeve. Bind the lower edge of the sleeve with the binding.
  7. Set the sleeves into the armholes, matching the notches and easing the sleeve cap at the top. Attach the shoulder pads.
  8. Make buttonholes on the right front and sew the buttons onto the left front.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?