Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4432
#4434

Fitted Draped V-Neck Jacket

Pattern #4433

A fitted, fully lined women's jacket with a collarless V-neckline, a pleated cascade falling from the right shoulder down the front edge, a single-button closure and rounded front hems. Princess seams front and back, two-piece set-in sleeves. Drafted to your own measurements. Recommended fabric: lightweight suiting fabrics of natural or blended fibres.

Tech. Description

Fitted Draped V-Neck Jacket

A fitted, fully lined women's jacket with a collarless V-neckline, a pleated cascade falling from the right shoulder down the front edge, a single-button closure and rounded front hems. Princess seams front and back, two-piece set-in sleeves.

When To Wear

  • At the office over a blouse or top with trousers or a pencil skirt.
  • In spring and autumn over a dress for daytime events.

Key Design Features

Silhouette: Fitted, shaped by princess seams from the armholes and darts on the centre front and centre back pieces; hip length.

Neckline: Collarless V-neckline, faced, with a fusible stay tape along the front neckline.

Front: Asymmetric. Two cascade pieces are joined to the right front and form a draped decorative collar; its pleats are held with blind stitches on the wrong side. Front edges curve into rounded hems.

Closure: One button; buttonhole on the right front.

Sleeves: Long two-piece set-in sleeves with an eased cap and interfaced hems.

Back: Centre back seam and princess seams; a separate back hem facing joined to the front facings.

Finishing: Front edge seam understitched onto the facing 0.2 cm from the seam; thin shoulder pads.

Lining: Full lining, bagged through an opening in the left sleeve elbow seam and attached to the sleeve hems.

Level Of Difficulty

Advanced. Fully interfaced fronts, a draped cascade with hand-secured pleats, facings for the neckline and hem, two-piece sleeves and a bagged lining.

Fabric Recommendations

Lightweight suiting fabrics of natural or blended fibres.

Additional Supplies

  • Lining fabric
  • Fusible interfacing (facings, centre and side fronts, back neck and hem facings, sleeve hems)
  • Fusible stay tape for the front neckline
  • Thin shoulder pads
  • 1 button

Cutter's Must

From main fabric:

  • Back Center – 2 pieces
  • Back Side – 2 pieces
  • Front Side – 2 pieces
  • Front Right Center – 1 piece
  • Front Left Center – 1 piece
  • Front Left Facing – 1 piece
  • Front Right Facing – 1 piece
  • Back Neckline Facing – 1 piece
  • Sleeve Upper – 2 pieces
  • Sleeve Lower – 2 pieces
  • Cascade Collar 1 – 1 piece
  • Cascade Collar 2 – 1 piece
  • Back Hem Facing – 1 piece

From lining fabric:

  • Back Center – 2 pieces
  • Back Side – 2 pieces
  • Front Side – 2 pieces
  • Front Lining – 2 pieces
  • Sleeve Upper – 2 pieces
  • Sleeve Lower – 2 pieces

Attention: The back and front Side pieces from the lining fabric are cut subtracting the width of the back Neckline Facing and back Hem Facing respectively.

From fusible interfacing: Facing, back Neckline Facing, back Hem Facing, front Center, front Side, sleeve hem.

Sewing Instructions

  1. Fuse interfacing to the pieces. Along the neckline of the front, apply an additional fusible stay tape.
  2. Stitch the dart on the front Center. Press the dart upwards. Attach Cascade Collar 1 and Cascade Collar 2 to the right front. Press seam allowances open. Stitch and press open the panel seam on the front.
  3. Stitch the dart on the back Center. Stitch and press open the panel seams on the back. Stitch and press open the center back seam. Stitch and press open the shoulder and side seams of the jacket.
  4. Stitch and press open the shoulder seams of the back Neckline Facing and the Facing. Attach the back Hem Facing to the Facings. Press seams open.
  5. Place the Facing with its facing onto the right side of the front, right side down, pin, and stitch the front edge, front neckline, back neckline, and the bottom of the jacket. Stitching is done from the front side. Topstitch the seam allowance of the front edge stitching onto the Facing. The stitching should be 0.2 cm from the seam.
  6. Stitch and press open the elbow seam of the sleeve, easing the upper of the sleeve and matching the notches. Press the sleeve hem. Turn back the hem allowance, stitch and press open the front seam of the sleeve.
  7. Set the sleeves into the armholes according to the notches, easing the sleeve cap at the top. Attach shoulder pads.
  8. On the lining fabric pieces, stitch the seams and set in the sleeves, leaving an opening for turning in the left elbow seam. Attach the lining to the inner edges of the front Facings and of the back Neckline Facing and back Hem Facing.
  9. Attach the lining to the sleeve hem. Turn the jacket right side out. Stitch the technical opening closed.
  10. On the right front, make a buttonhole; on the left front, sew on a button.
  11. Fold and secure the pleats on the decorative collar with blind stitches from the wrong side.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?