Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4427
#4429

Lace Yoke Shift Dress with Keyhole

Pattern #4428

An above-knee women's dress with a flared A-line body, lace yokes and short lace sleeves, a banded round neckline and a back opening fastened with three buttons and rouleau loops. Drafted to your own measurements. Recommended fabric: dress fabrics of natural or blended fibres for the body; lace fabric for the yokes and sleeves.

Tech. Description

Lace Yoke Shift Dress

An above-knee women's dress with a flared A-line body, lace yokes and short lace sleeves, a banded round neckline and a back opening fastened with three buttons and rouleau loops.

When To Wear

  • In spring and summer for daytime, with flat sandals or low pumps.
  • For dinners and family celebrations, where the lace sections show at the shoulders.

Key Design Features

Silhouette: Loose A-line, flaring from the yoke to the hem; front cut in one piece, back in two.

Length: Above the knee.

Neckline: Round, with a band cut from the main fabric: the outer neck facing is stitched to the right side of the dress and backed with an interfaced inner facing.

Sleeves: Short set-in sleeves in lace, hems overlocked, turned up and topstitched.

Front: Lace yoke sections joined to the front at the shoulders, running from the neckband into the armholes.

Back: Centre back seam with an open slit below the neckline; matching lace yoke sections.

Closure: Three buttons at the back neck with rouleau loops made from a bias strip and set into the facing seam.

Finishing: Hem turned under twice by 1 cm and topstitched.

Level Of Difficulty

Intermediate. Joining lace to dress fabric, a faced neckband with a back slit, rouleau loops and set-in sleeves.

Fabric Recommendations

Dress fabrics of natural or blended fibres for the body; lace fabric for the yokes and sleeves.

Additional Supplies

  • Lace fabric
  • Fusible interfacing (neck facings)
  • 3 buttons

Cutter's Must

From main fabric:

  • Back - 2 pieces
  • Front - 1 piece
  • Back neck facing – 4 pieces
  • Front neck facing – 2 pieces

From lace fabric:

  • Back yoke - 2 pieces
  • Front yoke - 2 pieces
  • Sleeve — 2 pieces

From fusible interfacing:

  • Back neck facing – 2 pieces
  • Front neck facing – 1 piece

Sewing Instructions

  1. Fuse fusible interfacing to the facing pieces.
  2. Stitch the back yoke to the back, press seam allowances towards the back, serge. Stitch the front yoke to the front, press seam allowances towards the front, serge.
  3. Stitch the outer back neck facing to the back, clip seam allowances and press towards the facing. Stitch the outer front neck facing to the front, clip seam allowances and press towards the facing.
  4. Serge the center back edges separately on each piece. Stitch the center back seam from the mark to the hem. Press seam allowances open, pressing the slit.
  5. Stitch the side and shoulder edges, press seam allowances towards the back and serge.
  6. Cut a bias binding 2.5 cm wide and 15 cm long. Fold the strip in half lengthwise, right sides together, and stitch 0.3 cm from the fold. Trim seam allowances close to the stitching, turn the strip right side out and straighten the rouleau. Cut loops. The length of one loop is approximately 4 cm.
  7. Stitch the shoulder edges of the inner neck facings, press seam allowances open. Place the dress with the facing right sides together, aligning the neck edges. Stitch the neck edge and center edges, inserting the rouleau loops. Clip seam allowances at curves, turn pieces right side out and press. Turn under the lower edge of the inner facing and topstitch into the seam of the outer facing. Sew on buttons.
  8. Stitch the sleeve edge, press seam allowances and serge. Set the sleeves into the armholes, matching notches. Press seam allowances and serge. Serge the lower sleeve edge, press to the wrong side and topstitch.
  9. Turn under the lower edge of the garment by 1 cm, then another 1 cm, and topstitch.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?