Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4419
#4421

Blouse with Round Neckline & V Keyhole

Pattern #4420

A women's loose pullover blouse with a round neckline and a V-shaped keyhole at the centre front, closed at the neck by a decorative clasp. It has a back yoke over a pleated back, a longer curved back hem and long sleeves gathered into buttoned cuffs. Drafted to your own measurements. Recommended fabric: blouse fabrics of natural or blended fibres.

Tech. Description

Blouse with Round Neckline & V Keyhole

A women's loose pullover blouse with a round neckline and a V-shaped keyhole at the centre front, closed at the neck by a decorative clasp. It has a back yoke over a pleated back, a longer curved back hem and long sleeves gathered into buttoned cuffs.

When To Wear

  • For the office with trousers or a pencil skirt, tucked in or worn loose.
  • Under a jacket or cardigan in spring and autumn.

Key Design Features

Silhouette: Loose, straight blouse.

Length: Hip length at the front; the back hem is longer and curved.

Neckline: Round neckline bound with a narrow bias binding; the binding ends pass through the slits of a decorative clasp at the top of the keyhole. Small pleats fall from the neckline on the front.

Front: Centre front seam running from the bottom of the V keyhole to the hem; the keyhole is finished with a facing.

Sleeves: Long sleeves set into an open armhole, sewn up together with the side seams; gathered into a cuff with a cut-on extension, one button and buttonhole. The sleeve slit is bound with bias binding.

Back: Back yoke; the back is cut on the fold with pleats turned towards the centre.

Finishing: Seams overlocked; hem overlocked, turned up 1.5 cm and topstitched.

Level Of Difficulty

Intermediate. A faced keyhole, a bias-bound neckline with a clasp, bound sleeve slits, cuffs with an extension, buttonholes.

Fabric Recommendations

Blouse fabrics of natural or blended fibres.

Additional Supplies

  • Fusible interfacing (cuffs, front keyhole facings)
  • 2 buttons
  • Decorative clasp for the neckline

Cutter's Must

From main fabric:

  • Back Yoke – 1 piece
  • Back — 1 piece on fold
  • Front — 2 pieces
  • Sleeve — 2 pieces
  • Cuff — 2 pieces
  • Front facing — 2 pieces

From fusible interfacing:

  • Cuff - 2 pieces
  • Front facing — 2 pieces

Sewing Instructions

  1. Fuse fusible interfacing to cuffs and facings.
  2. Lay and secure pleats on the back (depths directed towards the center). Stitch the back yoke to the back, press seam allowances upwards and overlock.
  3. Stitch the center seam of the front from the notch to the bottom, press seam allowances open, overlock. Stitch the center seam of the front neckline facing from the notch to the bottom, press seam allowances open. Overlock the outer edges. Place the facing with the garment right sides together and stitch the neckline. Turn the facing to the wrong side, straighten, press. Secure the neckline edge of the facing to the neckline edge of the main garment.
  4. Stitch the shoulder seams, press seam allowances towards the back and overlock.
  5. Cut a bias binding 4 cm wide, with a length equal to the neckline length + 4 — 5 cm. Press the trim strip in half lengthwise, fold the outer edges towards the center and press again. Bind the neckline, simultaneously finishing the ends. Thread the ends of the neckline trim strip through the fastener slits and topstitch.
  6. Make a slit on the sleeve along the marked line. Cut a bias binding from the main fabric 4 cm wide and a length equal to twice the slit length +4 cm. Fold the trim strip in half lengthwise and press. Press the outer seam allowances towards the center. Finish the sleeve slit with bias binding.
  7. Set the sleeve into the open armhole. Overlock seam allowances and press towards the sleeve.
  8. Stitch the side seam simultaneously with the sleeve seam. Overlock the seam allowance and press towards the back.
  9. Along the lower edge of the sleeve, sew a stitch with a loosely tensioned thread and gather.
  10. Fold the cuff in half lengthwise, right side in, and stitch the short sides and the step. Start the stitch strictly at the marked line for attaching the cuff to the sleeve. At the notch, clip the seam allowances, turn the cuff out and press. Attach the outer side of the cuff to the bottom of the sleeve. Fold the inner side of the cuff under and topstitch into the attachment seam.
  11. Overlock the bottom edge of the garment, press to the wrong side and topstitch.
  12. Make buttonholes on the cuffs. Sew on buttons.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?