Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4410
#4412

Sleeveless Fit-and-Flare High-Low Hem Dress

Pattern #4411

A women's sleeveless dress with a fitted darted bodice, a seam at the natural waist and a flared skirt with a high-low hem, shorter at the front and longer at the back. Zipper at the centre back. Drafted to your own measurements. Recommended fabric: dress fabrics made from natural or blended fibres with added elastane.

Tech. Description

High-Low Hem Fit-and-Flare Dress

A women's sleeveless dress with a fitted darted bodice, a seam at the natural waist and a flared skirt with a high-low hem, shorter at the front and longer at the back. Zipper at the centre back.

When To Wear

  • For summer parties, weddings and evening events.
  • In spring and autumn with a short jacket or cardigan over the bodice.

Key Design Features

Silhouette: Fit-and-flare: fitted bodice shaped with darts, flared skirt from the waist seam.

Length: High-low hem: above the knee at the front, dropping to below the knee at the back.

Neckline: Round neckline finished with an interfaced facing.

Sleeves: Sleeveless; armholes finished with a 4 cm bias binding turned to the inside and topstitched.

Front: Upper and lower front each cut in one piece on the fold, joined at the waist.

Back: Darts, a waist seam and a centre back seam with a zipper.

Finishing: Hem turned up and topstitched.

Level Of Difficulty

Beginner. Few pieces, darts, a waist seam, a faced neckline, bias-bound armholes and a centre back zipper; the curved high-low hem needs careful pressing.

Fabric Recommendations

Dress fabrics made from natural or blended fibres with added elastane.

Additional Supplies

  • Fusible interfacing (neckline facings)
  • Zipper
  • Bias binding, 4 cm wide (or cut from the main fabric)

Cutter's Must

From main fabric:

  • Upper back – 2 pieces
  • Lower back – 2 pieces
  • Upper front – 1 piece on fold
  • Lower front – 1 piece on fold
  • Front neckline facing — 1 piece
  • Back neckline facing — 2 pieces

From fusible interfacing:

  • Front neckline facing — 1 piece
  • Back neckline facing — 2 pieces

Sewing Instructions

  1. Fuse fusible interfacing to the respective pieces.
  2. Stitch darts on back pieces, press seam allowances towards the center. Stitch lower and upper back pieces. Overlock seam allowance and press downwards. Overlock center edges of back separately on each piece. Stitch the center edge of the back from the zipper mark to the bottom, press seam allowances open. Insert the zipper.
  3. Stitch darts on front pieces, press seam allowances towards the center. Stitch lower and upper front pieces. Overlock seam allowance and press downwards.
  4. Stitch shoulder edges. Press seam allowances towards the back and overlock.
  5. Stitch shoulder edges of facings. Press seam allowances open. Overlock the outer edge of the facing. Place the facing onto the neckline and stitch. Clip seam allowances, turn the facing to the wrong side and press.
  6. Cut (if not pre-made) bias binding 4 cm wide and a length equal to the armhole length + 5 cm. Fold the bias binding in half lengthwise, right side out, and press. Place the trim strip with the armhole edge on the right side and stitch. Clip notches. Fold the trim strip to the wrong side and topstitch along the fold to the main piece. Press the seam.
  7. Stitch side edges. Press seam allowances towards the back and overlock.
  8. Overlock the bottom edge of the garment. Press the hem allowance to the wrong side and topstitch.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?