Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4403
#4405

Sleeveless Sheath Dress with Draped Front

Pattern #4404

A knee-length women's sleeveless sheath dress with a horizontal seam across the front at the waist, pleated drape on the lower front gathered under a fabric tab on one side, and an invisible zipper in the centre back seam. Drafted to your own measurements. Recommended fabric: dress fabrics with good drape, made from natural or blended fibres.

Tech. Description

Sheath Dress with Draped Front

A knee-length women's sleeveless sheath dress with a horizontal seam across the front at the waist, pleated drape on the lower front gathered under a fabric tab on one side, and an invisible zipper in the centre back seam.

When To Wear

  • At the office in spring and summer, or under a jacket in cooler months.
  • For dinners, receptions and family celebrations.

Key Design Features

Silhouette: Fitted sheath, shaped with darts on the upper front and on the back.

Length: Knee length.

Neckline: Round neckline finished with an interfaced facing.

Sleeves: Sleeveless; armholes finished with a 4 cm bias binding turned to the inside and topstitched.

Front: Upper and lower front joined by a seam at the waist. The lower front is pleated towards one side; a separate decorative piece, laid in loose pleats towards the side seam, is topstitched over it, and a folded tab covers the gathered ends of the pleats.

Back: Centre back seam with an invisible zipper, back darts, no waist seam.

Finishing: Inner edge of the decorative piece hand-stitched to the pleat allowances; facing attached to the zipper tape; hem turned up and topstitched.

Level Of Difficulty

Intermediate. Pleated drape with a layered decorative piece and tab, an invisible zipper, a faced neckline and bias-bound armholes.

Fabric Recommendations

Dress fabrics with good drape, made from natural or blended fibres.

Additional Supplies

  • Invisible zipper
  • Fusible interfacing (neckline facings)
  • Bias binding, 4 cm wide (or cut from the main fabric)

Cutter's Must

From main fabric:

  • Back - 2 pieces
  • Upper front — 1 piece
  • Lower front - 1 piece
  • Back neckline facing – 2 pieces
  • Front neckline facing – 1 piece
  • Decorative front — 1 piece
  • Strap — 1 piece

From fusible interfacing:

  • Back neckline facing – 2 pieces
  • Front neckline facing – 1 piece

Sewing Instructions

  1. Fuse fusible interfacing to the neckline facing pieces.
  2. Stitch darts on the back, trim seam allowances to 1 cm and press towards the center.
  3. Serge the center edges of the back separately. Stitch the center edge of the back from the zipper mark to the bottom edge, press seam allowances open. Insert the zipper.
  4. Fold the strap right sides together along the indicated line and stitch along two edges. Turn the strap right side out and press.
  5. Stitch darts on the upper front, trim seam allowances to 1 cm and press towards the center.
  6. On the lower front, create pleats. If necessary, slash the area between the pleats and the left. Secure the pleats together. Serge the seam allowances of the pleats and the left. Serge the bottom, center, and top seam allowances of the decorative piece. Fold the top seam allowance inwards and press. Place the piece on the front right side up to the indicated line. Insert the strap between the piece and the front, so that when turned upwards, it covers the seam allowances of the decorative piece and the pleats. Topstitch the decorative piece and the strap. Fold the attached pieces upwards and align the top edge of the strap with the top edge of the lower front. Attach the lower front to the upper, press seam allowances upwards and serge. On the decorative piece, create arbitrary pleats and align them with the side seam. Hand stitch the inner edge of the piece to the pleat seam allowances.
  7. Stitch the side and shoulder edges, press seam allowances towards the back and serge.
  8. Cut (if not ready-made) a bias binding 4 cm wide and a length equal to the armhole length + 5cm. Fold the bias binding in half lengthwise right side out and press. Place the binding with the armhole edge right sides together and stitch. Clip the seam allowances. Fold the binding to the wrong side and topstitch along the fold to the main piece. Press the seam.
  9. Stitch the shoulder and side edges of the facings. Press seam allowances open. Serge the center edges and the outer edge of the facing. Place the dress with the facing right sides together and stitch the neckline. Clip seam allowances at curves, turn the facing out, straighten and press. Stitch the armhole in two steps: first the back, then the front. Clip seam allowances at curves, turn out, press. Secure the facing to the garment at the side seam allowances. Attach the facing to the zipper tape.
  10. Serge the bottom edge of the dress, press to the wrong side and topstitch.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?