Pleated Front Stand Collar Blouse
A women's semi-fitted blouse with a curved front yoke laid in box pleats, a buttoned stand collar, a button front on separate plackets and long sleeves with buttoned cuffs.
When To Wear
- At the office, with skirts, trousers and jackets.
- Worn loose or with a self-fabric belt at the waist.
Key Design Features
Silhouette: Semi-fitted, hip length; the back is shaped with darts.
Collar: Interfaced stand collar fastened with a button.
Front: A curved yoke with box pleats fanning from the neckline is joined to each front. Separate interfaced plackets, folded in half and topstitched; buttonholes on the right front, buttons on the left.
Sleeves: Long set-in sleeves with a short opening at the lower sleeve seam, finished with interfaced buttoned cuffs.
Back: Two halves with a centre back seam and darts.
Finishing: Hem allowance 1.5 cm, overlocked, turned up and topstitched. An optional straight belt can be cut from the main fabric to any length and width.
Level Of Difficulty
Intermediate. Box pleats on a curved yoke, separate button plackets, a stand collar, cuffs and buttonholes.
Fabric Recommendations
Blouse fabric of natural or blended fibres.
Additional Supplies
- Fusible interfacing (collar stand, plackets, cuffs)
- 12 buttons
Cutter's Must
From main fabric:
- Back - 2 pieces
- Front yoke - 2 pieces
- Front - 2 pieces
- Placket – 2 pieces
- Collar stand – 2 pieces
- Sleeve – 2 pieces
- Cuff – 2 pieces
From fusible interfacing:
- Collar stand – 1 piece
- Placket – 2 pieces
- Cuff – 2 pieces
Sewing Instructions
- Fuse the corresponding pieces with fusible interfacing.
- Fold the collar stand pieces right sides together and stitch the outer edge. Start and end the stitching strictly at the marked seam line for attaching the collar stand. Turn the finished collar stand right side out and press.
- Stitch the darts on the back. Press the darts towards the center seam. Stitch the center back seam. Press the seam to the left and serge.
- Form and secure the box pleats on the front yoke. Attach the yoke to the front, press the seam allowances towards the front and serge.
- Press the plackets in half lengthwise, right side out. Stitch the outer edge of the placket to the front. Press the seam towards the placket. Fold the inner edge of the placket inwards and topstitch into the attachment seam.
- Stitch the shoulder and side seams. Press the seam allowances towards the back and serge.
- Attach the upper collar stand to the neckline, fold under the raw edge of the lower collar stand and topstitch into the attachment seam of the upper collar stand.
- Serge the sleeve edges. Stitch the sleeve seam from the mark upwards, press the seam allowances open. Stitch a securing line along the fold 0.2 cm from the edge. Set the sleeves into the armholes. Serge the seam allowances and press towards the sleeve. Fold the cuff in half lengthwise, right sides together, and stitch the side edges. Turn the piece right side out, press. Attach the outer side of the cuff to the sleeve, fold under the seam allowance of the inner side of the cuff and topstitch into the attachment seam of the outer cuff.
- Serge the bottom edge of the garment, press to the wrong side and topstitch.
- On the right front, make buttonholes; on the left, sew on buttons. Make buttonholes and sew on buttons on the collar stand and cuffs.
- Tip: The blouse can be worn with a belt. Cut a piece of desired length and width from the main fabric (including seam allowances). Fold the belt in half lengthwise, right sides together, and stitch along the contour, leaving an opening for turning. Trim the seam allowances at the corners, turn the belt right side out. Close the opening.