Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4360
#4362

Fitted Dress with Pleated Bridge

Pattern #4361

A fitted knee-length women's dress with a seam at the waist, short cap sleeves and a gathered trim on the bodice that falls from the shoulder to the waist seam and is held at the neckline by a narrow fabric bridge. Invisible zipper in the centre back seam. Drafted to your own measurements. Recommended fabric: dress fabrics of natural or blended fibres with added elastane.

Tech. Description

Fitted Dress with Pleated Bridge

A fitted knee-length women's dress with a seam at the waist, short cap sleeves and a gathered trim on the bodice that falls from the shoulder to the waist seam and is held at the neckline by a narrow fabric bridge. Invisible zipper in the centre back seam.

When To Wear

  • At the office, on its own or under a jacket.
  • For daytime events and dinners in spring and summer.

Key Design Features

Silhouette: Fitted, with a straight skirt and a horizontal waist seam at front and back; darts in the bodice and skirt pieces.

Length: About knee length.

Neckline: Wide round neckline finished with facings.

Sleeves: Short set-in cap sleeves with a turned and topstitched hem; the armhole seam is finished with folded bias binding.

Front: A separate trim piece with a bias-bound outer edge is laid over one side of the upper front and caught into the neckline, armhole, side and waist seams. At the neckline it is gathered and fixed under a bridge, a narrow stitched tube that is topstitched over the folds and turned up to the neckline edge. The upper front darts are trimmed and overcast.

Back: Centre back seam with an invisible zipper, darts in the upper and lower back, seam at the waist.

Finishing: Neckline facings hand-tacked to the shoulder seams and sewn to the zipper tape; hem blind-stitched by hand.

Level Of Difficulty

Intermediate. An invisible zipper, a bias-bound trim gathered under a bridge, faced neckline and bias-bound armhole seams.

Fabric Recommendations

Dress fabrics of natural or blended fibres with added elastane.

Additional Supplies

  • Invisible zipper
  • Fusible interfacing (neckline facings)
  • Bias binding for the trim edge and the armholes (or bias strips cut 4 cm wide)

Cutter's Must

From main fabric:

  • 1. Upper back - 2 pieces
  • 2. Lower back - 2 pieces
  • 3. Upper front – 1 piece
  • 4. Lower front - 1 piece
  • 5. Front Trim - 1 piece
  • 6. Sleeve — 2 pieces
  • 7. Bridge — 1 piece
  • 8. Back neckline facing - 2 pieces
  • 9. Front neckline facing — 1 piece

Sewing Instructions

  1. Fuse the neckline facings.
  2. Stitch darts on the back pieces. Press darts towards the center seam. Stitch the upper and lower back PANELs. Press the seam downwards and serge. Serge the center edges of the back separately. Stitch the center edge from the zipper notch to the bottom. Insert the zipper.
  3. Stitch darts on the front pieces. On the upper front PANELs, trim and serge the dart depth. Press darts towards the center of the front.
  4. Finish the outer edge of the trim with bias binding. Place the trim on the front right side up and secure along the neckline, armhole, side, and bottom edges. Stitch the upper and lower front PANELs. Press seam allowances downwards and serge.
  5. Stitch shoulder and side seam allowances, press seam allowances towards the back and serge.
  6. Fold the bridge in half and stitch the longitudinal edge. Turn the bridge right side out and press, centering the seam. Gather the trim piece as desired. Place the bridge wrong side up, aligning the bottom edge and the mark. Topstitch the bridge, securing the pleats. Fold the bridge upwards and align the top edge with the neckline edge.
  7. Stitch the shoulder seam allowances of the facings. Press seam allowances open. Serge the outer edge of the facings. Place the facings on the neckline and stitch. Clip seam allowances, turn the facing to the wrong side and press. Secure the facing to the shoulder seam allowances with hand stitches. Secure the facing to the zipper tape.
  8. Serge the bottom sleeve seam allowance, fold inwards and topstitch. Set the sleeve into the armhole.
  9. Cut (if not pre-made) bias binding 4 cm wide and a length equal to the armhole length + 5 cm. Fold the bias binding in half lengthwise right side out and press. Align the binding with the armhole edge on the right side and stitch. Clip seam allowances. Fold the binding to the wrong side and topstitch along the fold to the main piece. Press the seam.
  10. Serge the hem seam allowance of the dress, press to the wrong side and hem with blind stitches.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?