Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4089
#4091

Puffed Sleeve Pussy Bow Fitted Blouse

Pattern #4090

A women's fitted blouse at hip length with a gathered upper front joined to a paneled lower front, a tie collar worn as a bow, and long sleeves gathered at the cap and into wide two-button cuffs. Front button closure on a cut-on placket. Drafted to your own measurements. Recommended fabric: blouse fabric from natural or blended fibres.

Tech. Description

Puffed Sleeve Pussy Bow Fitted Blouse

A women's fitted blouse at hip length with a gathered upper front joined to a paneled lower front, a tie collar worn as a bow, and long sleeves gathered at the cap and into wide two-button cuffs. Front button closure on a cut-on placket.

When To Wear

  • For the office, with a pencil skirt or tailored trousers.
  • Under a jacket or cardigan in autumn and spring.

Key Design Features

Silhouette: Fitted; the lower front is cut in centre and side panels, the back is shaped with princess seams and darts.

Length: Hip length, straight hem.

Collar: A long tie collar folded lengthwise and set into the neckline, its free ends tied in a bow.

Neckline: A rounded opening at the centre front above the buttons, finished with interfaced front neckline facings.

Front: Upper front gathered between notches into a horizontal seam under the bust.

Closure: Cut-on button plackets with 5 buttons, buttonholes on the right front.

Sleeves: Long, set-in, gathered along the cap between marks and at the lower edge; the sleeve seam is stitched to a mark, leaving an opening at the wrist.

Cuffs: Wide interfaced cuffs, each with 2 buttons and buttonholes.

Finishing: Hem overlocked, turned up 1.5 cm and topstitched.

Level Of Difficulty

Intermediate. Gathering into a seam, a cut-on placket finished with a neckline facing, a tie collar attached by machine, cuffs with a sleeve opening and buttonholes.

Fabric Recommendations

Blouse fabric from natural or blended fibres.

Additional Supplies

  • Fusible interfacing (plackets, front neckline facings, cuffs)
  • 9 buttons

Cutter's Must

If the patterns have a double contour, they include seam allowances. If the contour is single, the patterns do not include seam allowances. Seam allowances: Hem allowance – 1.5 cm, all other seams – 1 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need (don't forget to account for paired and symmetrical pieces). When stitching pieces, pay attention to the notches - they must match!

From main fabric:

  • Upper Front – 2 pieces
  • Lower Center Front – 2 pieces
  • Lower Side Front – 2 pieces
  • Back – 1 piece
  • Back Side – 2 pieces
  • Sleeve – 2 pieces
  • Collar – 1 piece
  • Cuff – 2 pieces
  • Front Neckline Facing – 2 pieces

From fusible interfacing:

  • Cut-on placket strip – 2 pieces
  • Front Neckline Facing – 2 pieces
  • Cuff – 2 pieces

Sewing Instructions

  1. Fuse interfacing to the cut-on plackets, the Front Neckline Facings and the Cuffs.
  2. Stitch the darts on the Back and press them towards the centre. Stitch the princess seams (Back to Back Side). Overlock the allowances and press them towards the centre.
  3. Stitch the Lower Center Front to the Lower Side Front. Overlock the seam and press it towards the centre front.
  4. Run a gathering stitch (loose tension) along the lower edge of the Upper Front between the notches and gather. Stitch the Upper Front to the lower front. Overlock the seam and press it downwards.
  5. Overlock the outer edge of the Front Neckline Facing. Stitch the facing to the cut-on placket and press the allowance towards the placket. Fold the placket and facing back onto the right side and stitch along the neckline up to the mark. Clip into the neckline at the mark. Clip the allowance on the curves. Turn the facing to the wrong side and press. Turn under the placket allowance and topstitch.
  6. Stitch the shoulder and side seams. Overlock the seams and press them towards the back.
  7. Fold the Collar in half lengthwise, right sides together, and stitch the tie ends from the end mark to the fold. Clip the Collar allowance at the end mark. Trim the allowances at the corners and turn right side out. Stitch the outer edge of the Collar into the neckline. Turn under the allowance of the inner edge and topstitch it into the attaching seam of the outer edge.
  8. Overlock the side edges of the Sleeve. Stitch the sleeve seam up to the mark, leaving the wrist opening. Press the allowances open. Run a gathering stitch (loose tension) along the sleeve cap between the marks and along the lower edge of the sleeve, and gather. Set the sleeves into the armholes. Overlock the seam and press it towards the sleeve. Fold each Cuff lengthwise, right sides together, and stitch the ends and the section up to the notch, starting and ending the stitching exactly at the marked line. Clip the allowance at the mark. Trim the allowances and turn right side out. Stitch the outer edge of the Cuff to the sleeve. Turn under the inner edge and topstitch it into the attaching seam of the outer edge.
  9. Overlock the hem of the blouse, press it to the wrong side and topstitch.
  10. Make the buttonholes on the right front and sew the buttons on the left front. Make the buttonholes and sew on the buttons on the Cuffs.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?