Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4505
#4507

Fitted Sleeved Dress with Curved Front Panels

Pattern #4506

A fitted women's sheath dress with a round neckline and set-in sleeves below the elbow. The front is cut into panels along sweeping curved seams and made up in two fabrics; the back has a centre seam with a concealed zip and a slit at the hem. Drafted to your own measurements. Recommended fabric: dress fabrics of natural or blended fibres, in two colours or textures for the front panels.

Tech. Description

Fitted Sleeved Dress with Curved Front Panels

A fitted women's sheath dress with a round neckline and set-in sleeves below the elbow. The front is cut into panels along sweeping curved seams and made up in two fabrics; the back has a centre seam with a concealed zip and a slit at the hem.

When To Wear

  • To the office in autumn, winter and spring, with tights and closed shoes.
  • For daytime events and dinners, on its own or under a short jacket.

Key Design Features

Silhouette: Close-fitting sheath.

Length: Mid-calf length.

Neckline: Round, finished with interfaced facings; facing ends attached to the zip tape.

Sleeves: One-piece set-in sleeves ending below the elbow.

Front: Asymmetric panels with curved seams: a curved neckline panel joined to the central upper front, a left upper front with a side insert, and right and left lower fronts divided by a long curved seam that runs from the waist to the hem. The panels alternate between the two fabrics.

Back: Darts and a centre back seam ending in a slit at the hem, topstitched 0.2 cm from the edge.

Closure: Concealed zip in the upper part of the centre back seam.

Finishing: Dress hem turned up 2 cm and sleeve hems 1.5 cm, both blind-stitched by hand.

Level Of Difficulty

Intermediate. Joining curved seams accurately, matching two fabrics across asymmetric panels, a concealed zip with a facing and a back slit.

Fabric Recommendations

Dress fabrics of natural or blended fibres, in two colours or textures for the front panels.

Additional Supplies

  • Concealed zip
  • Fusible interfacing (neck facings)

Cutter's Must

From main fabric:

  • Collar - 1 piece
  • Front facing – 1 piece
  • Front side – 1 piece
  • Front lower right – 1 piece

From main fabric 1:

  • Front central upper - 1 piece
  • Back - 2 pieces
  • Front left upper - 1 piece
  • Front lower left – 1 piece
  • Sleeve - 2 pieces
  • Back facing – 2 pieces

From fusible interfacing:

  • Back facing – 2 pieces
  • Front facing – 1 piece

Sewing Instructions

  1. Fuse fusible interfacing to the facing pieces of the neckline.
  2. Stitch darts on the back pieces, press the seam allowances towards the center. Overlock the center back seam allowance separately on each piece. Stitch the center back seam from the zipper mark to the slit mark. Insert the zipper. Topstitch the seam allowances along the slit 0.2 cm from the edge.
  3. Attach the left upper front to the front side. Overlock the seam allowance and press it upwards. Attach the collar to the central upper front. Overlock the seam allowance and press it upwards. Stitch the upper front pieces together. Overlock the seam allowance and press it towards the center. Attach the lower side and the lower side insert of the front. Overlock the seam allowances and press them upwards.
  4. Stitch the side and shoulder seams, press the seam allowances towards the back and overlock.
  5. Stitch the shoulder seams of the facings. Press the seam allowances open and overlock. Overlock the outer edge of the facings. Place the dress with the facing right sides together, aligning the neckline edges. Before reaching 5 mm from the edges of the concealed fastener, fold back the facing and pin it to the upper edge of the dress. On the right side of the dress, fold back the seam allowances along the zipper and pin them to the neckline edge over the facing. Stitch the neckline edge. Clip the seam at the curves, turn the pieces right side out and press. Topstitch the seam allowances to the facing. Attach the facing to the zipper tape.
  6. Stitch the sleeve seam. Overlock the seam allowance and press it towards the back of the sleeve. Set the sleeve into the armhole, aligning the notches. Overlock the seam allowance.
  7. Overlock the hem allowance of the dress and sleeve hem, press to the wrong side and hem with blind stitches.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?