Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4480
#4482

Sleeved Paneled Dress with Front Pleats

Pattern #4481

A knee-length women's sheath dress cut in horizontal panels: a pleated upper bodice, a band under the bust, a curved hip panel and a straight lower skirt. Short cap sleeves are cut in two halves and seamed over the shoulder; the back closes with a zipper and has a slit at the hem. Drafted to your own measurements. Recommended fabric: dress fabrics from natural or blended fibres.

Tech. Description

Sleeved Paneled Dress with Front Pleats

A knee-length women's sheath dress cut in horizontal panels: a pleated upper bodice, a band under the bust, a curved hip panel and a straight lower skirt. Short cap sleeves are cut in two halves and seamed over the shoulder; the back closes with a zipper and has a slit at the hem.

When To Wear

  • At the office, with a jacket or cardigan over the short sleeves.
  • At daytime events and dinners in spring and summer.

Key Design Features

Silhouette: Fitted sheath, shaped by the panel seams rather than by darts on the front.

Length: Knee length.

Neckline: Round, finished with a folded bias binding turned to the inside and topstitched.

Sleeves: Short cap sleeves in two halves (front and back) joined by a seam over the shoulder, sewn to the front and back along seams running from the neckline to the underarm. The lower armhole is finished with bias binding.

Front: Upper front with pleats under the bust, their intake turned towards the side seams; a front band, a curved front hip panel and a lower front cut on the fold.

Back: The same panel lines as the front, with darts on the upper back pressed towards the centre and a centre back seam.

Closure: Concealed zipper in the centre back seam.

Finishing: Back slit at the hem, its allowances topstitched 0.1–0.2 cm from the edge; hem and sleeve edges turned and topstitched.

Level Of Difficulty

Intermediate. Matching horizontal and curved panel seams, pleats, a concealed zipper with a slit below it, and bias-bound edges.

Fabric Recommendations

Dress fabrics from natural or blended fibres.

Additional Supplies

  • Concealed zipper
  • Bias binding, 4 cm wide (or cut from fabric), for the neckline and lower armholes

Cutter's Must

From main fabric:

  • 1. Upper back – 2 pieces
  • 2. Back insert – 2 pieces
  • 3. Back skirt half insert – 2 pieces
  • 4. Lower back — 2 pieces
  • 5. Upper front -1 piece
  • 6. Front insert — 1 piece
  • 7. Front skirt half insert – 1 piece
  • 8. Lower front — 1 piece on fold
  • 9. Back sleeve — 2 pieces
  • 10. Front sleeve — 2 pieces

Sewing Instructions

  1. Stitch darts on back pieces. Press dart intake towards the center. Attach the back insert. Overlock the seam allowance and press it towards the insert. Attach the back skirt half insert. Overlock the seam allowance and press it towards the insert. Attach the lower skirt. Overlock the seam allowance and press it upwards.
  2. Overlock the center edges of the back separately. Stitch from the zipper mark to the slit mark. Press the seam allowance open. Insert the zipper. Topstitch the seam allowances along the slit 0.1 -0.2 cm from the edge.
  3. On the center front, create and secure the pleats. Direct the pleat intake towards the side seam. Stitch the front pieces similarly to the back pieces.
  4. Stitch the shoulder seams of the sleeves. Overlock the seam allowance and press it towards the back sleeve. Overlock the lower edge of the sleeve, fold inwards and topstitch. Attach the sleeves to the front and back. Overlock the seam allowances and press them towards the sleeve.
  5. Stitch the side seams. Overlock the seam allowances and press them towards the back.
  6. Cut (if not ready-made) a bias binding 4 cm wide and with a length equal to the length of the lower armhole + 4 cm. Fold the bias binding in half lengthwise, right side out, and press. Place the trim strip with the armhole edge, right side to right side, and stitch. Clip the seam allowances. Fold the trim strip to the wrong side and topstitch along the fold to the main piece. Press the seam.
  7. Cut (if not ready-made) a bias binding 4 cm wide and with a length equal to the neckline length. Fold the bias binding in half lengthwise, right side out, and press. Place the trim strip with the neckline edge, right side to right side, and stitch. Clip the seam allowances. Fold the trim strip to the wrong side and topstitch along the fold to the main piece. Press the seam.
  8. Overlock the lower edge of the garment. Fold to the wrong side, press, and topstitch.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?