Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4459
#4461

Sleeveless Stand Collar Dress with Bow

Pattern #4460

A women's sleeveless dress, fitted at the bust and waist and flared to an A-line hem, with princess seams front and back, a stand collar open at the centre front, a V-shaped front yoke and a fabric bow at the neckline. Drafted to your own measurements. Recommended fabric: dress fabrics of natural or blended fibres.

Tech. Description

Sleeveless Stand Collar Dress with Bow

A women's sleeveless dress, fitted at the bust and waist and flared to an A-line hem, with princess seams front and back, a stand collar open at the centre front, a V-shaped front yoke and a fabric bow at the neckline.

When To Wear

  • At the office in warm weather, or over a fine top in cooler months.
  • For daytime events and dinners.

Key Design Features

Silhouette: Fitted through the bust and waist, flaring from the princess seams to the hem; above-knee length.

Collar: Stand collar with a small opening at the centre front. The outer stand is joined to the front yoke and to the back; the inner stand, cut as separate pieces, is stitched to it along the top edge and the front opening.

Front: V-shaped yoke at the top, centre front seam, princess seams from the armholes to the hem. A bow, made separately and held by a small loop, is sewn at the neckline.

Back: Centre back seam and princess seams; the collar seam runs in a V on the back.

Sleeves: None; armholes finished with a folded bias strip turned to the inside and topstitched.

Closure: Invisible zipper in the left side seam.

Finishing: Seams overlocked; hem turned up and sewn with blind hand stitches.

Level Of Difficulty

Intermediate. A two-layer stand collar joined into the yoke and back seams, princess seams, an invisible side zipper and bias-bound armholes.

Fabric Recommendations

Dress fabrics of natural or blended fibres.

Additional Supplies

  • Fusible interfacing (outer collar pieces)
  • Invisible zipper
  • Bias binding, 4 cm wide, armhole length plus 5 cm per armhole (or cut from the dress fabric)

Cutter's Must

From main fabric:

  • Center back - 2 pieces
  • Side back - 2 pieces
  • Center front – 2 pieces
  • Side front - 2 pieces
  • Back collar - 4 pieces
  • Front collar - 4 pieces
  • Front yoke – 2 pieces
  • Bow – 1 piece

From fusible interfacing:

  • Back collar – 2 pieces
  • Front collar – 2 pieces

Sewing Instructions

  1. Fuse fusible interfacing to the upper collars.
  2. Attach the upper collar to the back. Press seam allowances towards the collar. Stitch the center seam of the back. Overlock seam allowances and press to the left side. Stitch the panel seams of the back. Overlock seam allowances and press towards the center.
  3. Attach the upper front collar to the front yoke. Press seam allowances towards the collar. Attach the front yoke to the front. Overlock seam allowances and press upwards. Stitch the panel seams of the front. Overlock seam allowances and press towards the center.
  4. Stitch the shoulder seams, simultaneously with the stand seam. Overlock seam allowances in the shoulder seam area. Clip and press open seam allowances in the collar area.
  5. Cut a bias binding 4 cm wide and a length equal to the armhole length + 5 cm (if not pre-made). Fold the bias binding in half lengthwise, right sides out, and press. Place the trim strip along the armhole edge on the right side and stitch. Clip seam allowances. Fold the trim strip to the wrong side and topstitch along the fold to the main piece. Press the seam.
  6. Stitch the right side seams, press seam allowances towards the back and overlock. Overlock the left side seams separately on each piece, stitch from the mark to the bottom, and press open. Insert the zipper.
  7. Stitch the shoulder and center seams of the inner collars. Press seam allowances open. Overlock the bottom edge. Place the inner collars on the neckline and stitch along the upper edge and the front section of the front. Clip seam allowances and turn to the wrong side. Press the upper edge. Topstitch the seam allowances of the inner collars into the seam of the upper collars.
  8. Fold the bow piece right sides together and stitch along three sides, leaving an opening for turning. Trim seam allowances at the corners, turn the bow right side out, and press. Hand-stitch the opening closed. Cut a loop 6 x 6 cm. Stitch along one side and turn. Insert the bow into the loop and sew to the dress, according to the technical sketch.
  9. Overlock the bottom edge of the dress, press to the wrong side, and hem with blind stitches.

Features

Order Pattern

Standard Sizes

Pro fitIndividual figure characteristics

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?