Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4439
#4441

Pleated Neck Blouse

Pattern #4440

A women's loose hip-length blouse with small pleats at the front neckline, long set-in sleeves and a hem gathered by elastic in a casing, fastened with one button and a loop at the back neck. Drafted to your own measurements. Recommended fabric: blouse fabrics of natural or blended fibres.

Tech. Description

Pleated Neck Blouse

A women's loose hip-length blouse with small pleats at the front neckline, long set-in sleeves and a hem gathered by elastic in a casing, fastened with one button and a loop at the back neck.

When To Wear

  • In autumn and spring with jeans, straight trousers or a pencil skirt.
  • For the office, under a jacket or cardigan.

Key Design Features

Silhouette: Loose body that blouses over the elasticated hem.

Length: Hip length.

Neckline: Round neckline finished with interfaced front and back facings; the front neckline is laid into pleats turned away from the centre.

Sleeves: Long sleeves set into the open armhole, with the side and sleeve seams stitched in one; the hem is turned into a casing with elastic, giving a gathered cuff edge.

Front: One piece cut on the fold, without darts.

Closure: Slit at the top of the centre back seam, faced together with the neckline, fastened with one button and a bias-cut rouleau loop.

Back: Two pieces with a centre back seam below the slit.

Finishing: The lower edge is turned up 2 cm into a casing with elastic. Shoulder and side seams overlocked and pressed towards the back; armhole seams pressed towards the sleeve.

Level Of Difficulty

Beginner. A one-piece front, a faced back slit with a turned loop, sleeves set in flat and elastic threaded through casings.

Fabric Recommendations

Blouse fabrics of natural or blended fibres.

Additional Supplies

  • Fusible interfacing (neckline facings)
  • 1 button
  • Elastic (hem and sleeve casings)

Cutter's Must

From main fabric:

  • Back — 2 pieces
  • Front — 1 piece on fold
  • Sleeve — 2 pieces
  • Back neck facing — 2 pieces
  • Front neck facing — 1 piece

From fusible interfacing:

  • Back neck facing — 2 pieces
  • Front neck facing — 1 piece

Sewing Instructions

  1. Fuse the facings with fusible interfacing.
  2. Form and secure the pleats on the front neckline (depths directed from the center).
  3. Stitch the center back seam allowances from the notch to the bottom edge, press seam allowances open and overlock.
  4. Stitch the shoulder seam allowances, press seam allowances towards the back and overlock.
  5. Cut a bias binding strip 3 cm wide and 7 cm long. Fold the strip in half lengthwise and stitch 0.3 cm from the fold. Trim the seam allowances and turn the piece right side out. Adjust the loop length.
  6. Stitch the center back seam allowances of the neck facings from the notch to the bottom, press seam allowances open. Stitch the shoulder seam allowances of the neck facings, press seam allowances open. Overlock the outer edge. Place the facing and the garment right sides together and stitch the slit and neckline edge, inserting the hanging loop. Trim seam allowances at corners, turn the facing to the wrong side, straighten, and press. Sew on the button.
  7. Set the sleeve into the open armhole. Overlock seam allowances and press towards the sleeve.
  8. Stitch the side seam allowances simultaneously with the sleeve seam allowances. Overlock seam allowances and press towards the back.
  9. Overlock the bottom edge of the garment and the sleeve hem, fold the seam allowances inwards and topstitch, forming a casing. Insert elastic into the casing and secure the ends.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?