Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4355
#4357

Sleeveless Crossover Bodice Pleated Dress

Pattern #4356

A women's sleeveless knee-length dress with a waist seam. Two diagonal crossover panels are layered over the fitted front bodice, and the skirt has inverted pleats stitched down 10 cm from the waist. Worn with a separate tie belt. Drafted to your own measurements. Recommended fabric: dress fabrics of natural or blended fibres.

Tech. Description

Sleeveless Crossover Bodice Pleated Dress

A women's sleeveless knee-length dress with a waist seam. Two diagonal crossover panels are layered over the fitted front bodice, and the skirt has inverted pleats stitched down 10 cm from the waist. Worn with a separate tie belt.

When To Wear

  • In spring and summer for daytime outings, brunches and garden parties.
  • With a cardigan or jacket for the office in cooler weather.

Key Design Features

Silhouette: Fitted bodice shaped with darts, waist seam, skirt flared by pleats.

Length: Knee length, hem turned up and topstitched.

Neckline: Wide round neckline.

Front: One-piece upper front with darts. Two crossover panels with a cut-on facing along the diagonal edge are sewn to a marked line on the bodice, folded down and lapped right over left, then caught into the armhole, side and waist seams.

Sleeves: Sleeveless.

Back: Upper back in two pieces with darts, centre back seam and a concealed zipper.

Skirt: Front and back each cut in two pieces, with inverted pleats stitched down 10 cm from the waist seam.

Waist: Separate tie belt, sewn as a folded strip and turned through an opening.

Finishing: Neckline and armholes finished with an all-in-one fused facing; the armholes are stitched in two steps (back, then front) and the facing is secured at the side seams and to the zipper tape.

Level Of Difficulty

Intermediate. Layered crossover panels, inverted pleats, a concealed zipper and an all-in-one neckline and armhole facing.

Fabric Recommendations

Dress fabrics of natural or blended fibres.

Additional Supplies

  • Concealed zipper
  • Fusible interfacing (neckline facings)

Cutter's Must

From main fabric:

  • Back upper - 2 pieces
  • Back lower - 2 pieces
  • Front upper - 1 piece
  • Front lower - 2 pieces
  • Diagonal front overlay - 2 pieces
  • Back neckline facing – 2 pieces
  • Front neckline facing – 1 piece
  • Belt - 1 piece

From fusible interfacing:

  • Back neckline facing – 2 pieces
  • Front neckline facing – 1 piece

Sewing Instructions

  1. Fuse fusible interfacing to the neckline facing pieces.
  2. Stitch darts on the upper back PANELs, trim seam allowances to 1 cm and press towards the center. On the lower back PANELs, create and stitch inverted pleats for 10 cm from the upper edge. Attach the upper back PANELs to the lower back PANELs, press seam allowances upwards and serge.
  3. Serge the center edges of the back separately. Stitch the center edge of the back from the zipper notch to the lower edge, press seam allowances open. Insert the zipper.
  4. Stitch darts on the upper front, trim seam allowances to 1 cm and press towards the center. On the lower front PANELs, create and stitch inverted pleats for 10 cm from the upper edge.
  5. Clip the upper edge of the diagonal front overlay at the notch and serge. Press the integrated bias binding of the diagonal edge to the wrong side. Place the overlay on the front right side to right side, aligning the attachment line of the overlay with the marked line on the front (the seam allowance of the upper edge of the overlay is directed downwards). Attach the overlay to the front, fold down, align the armhole, side, and lower seam allowances, placing the right overlay over the left. Then treat the front as one piece.
  6. Attach the lower front to the upper, press seam allowances upwards and serge.
  7. Stitch the side and shoulder edges, press seam allowances towards the back and serge.
  8. Stitch the shoulder and side edges of the FACINGs. Press seam allowances open. Serge the center edges and the outer edge of the facing. Place the dress and facing right sides together and stitch the neckline. Clip seam allowances at curves, turn the facing out, straighten and press. Stitch the armhole in two steps: first the back, then the front. Clip seam allowances at curves, turn out, press. Secure the facing to the garment at the side seam allowances. Attach the facing to the zipper tape.
  9. Serge the lower edge of the dress, press to the wrong side and topstitch.
  10. Fold the belt piece in half lengthwise, right sides together, and stitch, leaving a small opening for turning. Trim seam allowances at corners, turn the belt right side out and press. Stitch the opening closed.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?