Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4315
#4317

Shift Dress with Cap Sleeves and Bow Belt

Pattern #4316

A knee-length women's shift dress in lace knit with pleated cap sleeves and a wide round neckline bound with a silk band. Worn with a separate silk belt trimmed with a folded bow and a bead. Drafted to your own measurements. Recommended fabric: body: medium-stretch lace knit in natural or blended fibres.

Tech. Description

Shift Dress with Cap Sleeves and Bow Belt

A knee-length women's shift dress in lace knit with pleated cap sleeves and a wide round neckline bound with a silk band. Worn with a separate silk belt trimmed with a folded bow and a bead.

When To Wear

  • In late spring and summer for daytime celebrations, receptions and garden parties.
  • To the office with the belt left off and a jacket on top.

Key Design Features

Silhouette: Straight shift, with bust darts on the front; the front is cut in one piece on the fold.

Length: Knee length.

Neckline: Wide round neckline finished with a double silk band, interfaced on the outer layer and visible from the right side.

Sleeves: Silk cap sleeves, cut double (self-lined), with soft pleats turned towards the back; the seams run from the neckline into the armhole, and the underarm part of the armhole is turned in and topstitched.

Back: Centre back seam; no zip, the dress pulls on.

Waist: Separate silk belt with a strip topstitched along it, closed with two hooks and loops; a folded bow is sewn on and finished with a decorative bead.

Finishing: Hem turned up 1.5 cm and topstitched, with a twin needle or coverstitch.

Level Of Difficulty

Intermediate. Combining lace knit with silk, pleating and attaching lined cap sleeves, a double neck band and a folded bow.

Fabric Recommendations

Body: medium-stretch lace knit in natural or blended fibres. Sleeves, neck band, belt and bow: silk with elastane.

Additional Supplies

  • Fusible interfacing
  • 2 hooks and 2 loops
  • 1 decorative bead

Cutter's Must

If the patterns have a double contour, they include seam allowances. If the contour is single, the patterns do not include seam allowances. Seam allowances: Hem allowance – 1.5 cm, other seams 1 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need.

From knit fabric:

  • Back – 2 pieces
  • Front – 1 piece on fold

From silk:

  • Back Neckline Facing – 2 pieces
  • Front Neck Facing – 2 pieces
  • Sleeve – 4 pieces (2 pieces as lining)
  • Waistband – 1 piece
  • Waistband Placket – 1 piece
  • Bow – 1 piece

From fusible interfacing:

  • Front Neck Facing – 1 piece
  • Back Neckline Facing – 1 piece

Tip: Cut pieces from knit fabrics are sewn with a special elastic or narrow zigzag stitch. When serging with an overlock, trim seam allowances on knit fabric to 0.6 – 0.8 cm. The hem allowance is topstitched with a twin needle or on a coverstitch machine to maintain elasticity. You can also sew the pieces directly on a 3- or 4-thread overlock.

Sewing Instructions

When stitching pieces, pay attention to the notches - they must match!

  1. On the Front, mark and stitch the darts. Trim the dart depths with an overlock. Stitch the centre back seam. Press the seam.
  2. Place the Sleeve pieces together in pairs, right sides together, and stitch along the lower edge. Turn the pieces right side out and press. Baste each sleeve to its lining layer and from now on treat it as a single-layer piece. On the Sleeve, lay soft pleats according to the markings, with the pleat depths facing the back. Secure the pleats along the upper edge. Clip the armhole allowance of the Back and Front near the mark. Stitch the sleeves to the Back and Front. Press the seams towards the back and front.
  3. Stitch the side seams, serge, and press towards the back.
  4. Fuse the outer facings with interfacing. Stitch the Front Neck Facing to the Back Neckline Facing in pairs at the shoulders. Press the seams open. Place the two facing rings right sides together and stitch the inner edge. Turn right side out and press. Stitch the lower facing to the neckline edge. Press the seam towards the facing. Press the outer edge of the upper facing 1 cm to the inside and topstitch it into the seam that joins the lower facing.
  5. Serge the lower edge of the garment and the lower edge of the armholes. Fold to the wrong side, press, and topstitch.
  6. On the Waistband Placket, press the long sides to the wrong side by 1 cm. Topstitch the placket onto the Waistband along the marked line. Fold the Waistband in half lengthwise, right sides together, and stitch along three sides, inserting the hooks into one of the short sides and leaving an opening for turning in the long side. Turn the Waistband right side out, straighten the corners, and press. Close the opening. Adjust the Waistband length and sew on the loops for the hooks.
  7. Fold the Bow in half lengthwise and stitch along three sides, leaving an opening for turning in the long side. Turn the Bow right side out, straighten, and press. Close the opening. Stitch across the centre of the Bow along the marked line, stitching on the right side of the Bow. Fold the Bow along the fold lines: "outer" is an outer fold, "inner" is an inner fold. Fold the left side of the Bow symmetrically. Fold the topstitched part upwards and secure the folded Bow with stitches through all layers under the cross stitching. Sew the Bow to the Waistband. Sew the decorative bead over the resulting fold.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?