Knit Dress with Cascading Front Ruffle and Pleated Cap Sleeves

Name: Knit Dress with Cascading Front Ruffle and Pleated Cap Sleeves
Brand: Minerva Patterns
SKU: 4224
Price: 5.00 EUR
Availability: InStock

Pattern #4224

A knee-length women's dress in knit fabric, with an off-centre front seam holding a cascading flounce, short sleeves with soft pleats, and a round neckline finished with a folded band. Drafted to your own measurements. Recommended fabric: double-faced knit with medium stretch, in natural or blended fibres.

Tech. Description

Knit Dress with Cascading Front Ruffle and Pleated Cap Sleeves

A knee-length women's dress in knit fabric, with an off-centre front seam holding a cascading flounce, short sleeves with soft pleats, and a round neckline finished with a folded band.

When To Wear

For the office in summer, on its own or under a jacket.
For daytime outings and dinners in the warm season.

Key Design Features

Silhouette: Straight and close-fitting; a dart on the right front.

Length: Knee length; the flounce falls below the hem.

Neckline: Round, finished with a band folded in half and stretched onto the neckline; its seam sits at the centre back.

Sleeves: Short sleeves with soft pleats pointing downwards, secured along the armhole; the sleeve covers the upper part of the armhole and the lower armhole edge is turned and topstitched.

Front: Separate left and right fronts joined by a shaped seam to one side of the centre; a flounce is set into this seam from the neckline down, its outer edge finished with a narrow rolled hem.

Back: Centre back seam.

Finishing: Hems topstitched with a twin needle or on a coverstitch machine; seams can be sewn on a 3- or 4-thread overlocker.

Level Of Difficulty

Intermediate. Sewing knit fabric, a flounce with a rolled hem set into a shaped seam, pleated sleeves set into a partial armhole.

Fabric Recommendations

Double-faced knit with medium stretch, in natural or blended fibres.

Additional Supplies

None besides fabric and thread.

Cutter's Must

If the patterns have a double contour, they include seam allowances. If the contour is single, the patterns do not include seam allowances. Seam allowances: hem allowance and sleeve hem allowance – 1.5 cm, other seams 0.7 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need.

From main fabric:
- Back – 2 pieces
- Left front – 1 piece
- Right front – 1 piece
- Sleeve – 2 pieces
- Flounce – 1 piece
- Neckband - 1 piece

Tip: Knit fabric pieces are stitched with a special elastic or narrow zigzag stitch. The hem allowance is topstitched with a twin needle or on a coverstitch machine to maintain elasticity. You can also stitch pieces directly on a 3- or 4-thread overlocker.

Sewing Instructions

When stitching pieces, pay attention to the notches - they must match!

Finish the outer edge of the flounce with a narrow rolled hem. Overlock the straight edge of the flounce, fold inwards by 1 cm, and topstitch.
Mark and stitch the dart on the right front. Trim the depth with an overlocker. Stitch the shaped front seam, inserting the flounce into the seam. Press the seam.
Stitch the center back seam. Press the seam open.
On the sleeve, create soft pleats according to the markings. The pleat depths are directed downwards. Secure the pleats along the armhole. Overlock the lower sleeve allowance, fold inwards, and topstitch. Clip the armhole allowance of the back and front near the mark. Attach the sleeves to the back and front. Press the seam towards the back and front.
Stitch the side seams, overlock, and press towards the back.
Overlock the bottom edge of the garment and the bottom edge of the armhole. Fold to the wrong side, press, and topstitch.
Fold the neckband right sides together and stitch into a loop. Turn the piece right side out, fold in half lengthwise, and press. Attach the neckband to the neckline, stretching the edge and aligning the notches. The neckband seam is located at the center back seam.