Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4199
#4201

Fitted Blouse with Front Ruffle

Pattern #4200

A fitted women's blouse with a shirt collar on a stand, a pleated jabot on each side of the button placket and an upper front gathered into a seam under the bust. Long set-in sleeves with buttoned cuffs. Drafted to your own measurements. Recommended fabric: blouse fabrics of natural or blended fibres, for example satin.

Tech. Description

Fitted Blouse with Front Ruffle

A fitted women's blouse with a shirt collar on a stand, a pleated jabot on each side of the button placket and an upper front gathered into a seam under the bust. Long set-in sleeves with buttoned cuffs.

When To Wear

  • For the office under a jacket or with a pencil skirt.
  • For dinners and theatre with trousers or a skirt.

Key Design Features

Silhouette: Fitted, hip length.

Collar: Pointed shirt collar on a separate stand, fastened with a button on the stand.

Front: Upper front gathered between notches into a seam under the bust; lower front in centre and side pieces joined by vertical seams. A double-layer jabot with pleats at its upper edge runs down each side from the neckline to the under-bust seam.

Closure: Separate folded button placket on each front, buttonholes on the right front.

Sleeves: Long, one-piece, set-in; the sleeve seam is left open at the lower end above the cuff.

Back: Centre back seam and vertical darts.

Finishing: Cuffs with one button each; hem pressed up 1.5 cm and topstitched.

Level Of Difficulty

Intermediate. A collar on a stand, separate plackets, gathering into a seam, a lined and pleated jabot and cuffs set onto an opening.

Fabric Recommendations

Blouse fabrics of natural or blended fibres, for example satin.

Additional Supplies

  • Fusible interfacing (plackets, cuffs, upper collar, inner collar stand)
  • 10 buttons

Cutter's Must

If the patterns have a double contour, they include seam allowances. If the contour is single, the patterns do not include seam allowances. Seam allowances: Hem allowance – 1.5 cm, other seams – 1 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need (do not forget to account for paired and symmetrical pieces).

From main fabric:

  • Back – 2 pieces
  • Upper Front – 2 pieces
  • Lower Side Front – 2 pieces
  • Lower Center Front – 2 pieces
  • Placket – 2 pieces
  • Jabot – 4 pieces
  • Collar – 2 pieces
  • Stand Collar – 2 pieces
  • Sleeve – 2 pieces
  • Cuff – 2 pieces

From fusible interfacing:

  • Collar – 1 piece
  • Stand Collar – 1 piece
  • Placket – 2 pieces
  • Cuff – 2 pieces

Sewing Instructions

When stitching pieces, pay attention to the notches - they must match!

  1. Fuse interfacing to the Plackets, the Cuffs, the upper Collar and the inner Stand Collar.
  2. Place the upper and under Collar right sides together. Stitch the ends and the outer edge of the Collar. Trim the allowances. Turn the Collar right side out, shape and press. Place the Stand Collar pieces right sides together with the finished Collar between them, match the notches and stitch, stitching the ends of the stand at the same time. Start and end the stitching exactly at the marked stand attachment seam line. Turn the stand right side out and press.
  3. Stitch the Lower Center Front to the Lower Side Front. Overlock the seam and press it towards the centre front.
  4. Run a gathering stitch (loose tension) along the lower edge of the Upper Front between the notches and gather. Stitch the Upper Front to the lower front. Overlock the seam and press it downwards.
  5. Place the Jabot pieces right sides together in pairs and stitch the outer edge. Clip the allowances on the curves, turn right side out, baste the edge and press. Fold and baste the pleats along the upper edge at the marked lines. Place the Jabot on the front and baste it along the neckline and the centre front edge.
  6. Press each Placket in half lengthwise, wrong sides together. Stitch the outer edge of the Placket to the front. Press the seam towards the placket. Turn under the inner edge of the Placket and topstitch it into the attaching seam.
  7. Stitch the darts on the Back pieces. Press the darts towards the centre back. Stitch the centre back seam. Overlock the seam and press.
  8. Stitch the shoulder and side seams. Overlock the allowances and press them towards the back.
  9. Stitch the outer Stand Collar, with the Collar, into the neckline; turn under the open edge of the inner Stand Collar and topstitch it into the attaching seam of the outer stand.
  10. Overlock the sleeve seam edges. Stitch the sleeve seam from the mark upwards, leaving the lower end open, and press the allowances open. Set the sleeves into the armholes. Overlock the allowances and press them towards the sleeve. Fold each Cuff in half lengthwise, right sides together, and stitch the short ends, starting and ending the stitching exactly at the marked attachment line. Turn the Cuff right side out and press. Stitch the outer layer of the Cuff to the sleeve, turn under the allowance of the inner layer and topstitch it into the attaching seam of the outer layer.
  11. Overlock the hem of the blouse, press it to the wrong side and topstitch.
  12. Make the buttonholes on the right front and sew the buttons on the left front. Make the buttonholes and sew on the buttons on the Stand Collar and the Cuffs.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?