Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#5236
#5238

Reversible Shawl-Collar Bathrobe

Pattern #5237

A long women's wrap robe made of two complete layers, one in the main fabric and one in a contrasting fabric, so it can be worn either side out. It has a shawl collar cut in one with the fronts, a welt chest pocket, side-seam pockets and a two-tone tie belt. Drafted to your own measurements. Recommended fabric: dense silk or cotton fabrics for both layers, in two colours or prints.

Tech. Description

Reversible Shawl-Collar Bathrobe

A long women's wrap robe made of two complete layers, one in the main fabric and one in a contrasting fabric, so it can be worn either side out. It has a shawl collar cut in one with the fronts, a welt chest pocket, side-seam pockets and a two-tone tie belt.

When To Wear

  • At home in the morning and evening, over pyjamas or a nightgown.
  • After a bath or shower, tied at the waist with the belt.

Key Design Features

Silhouette: Loose, straight cut with a wrap front, drawn in at the waist by the tie belt.

Length: Below the knee.

Collar: Shawl collar cut in one with the fronts, joined by a centre back seam and set into the back neckline; the shoulder seams are stitched up to the corner and clipped there.

Sleeves: Set-in, with a lowered shoulder line, ending above the wrist; outer and inner sleeves are topstitched together at the hem and turned back as a contrast cuff.

Pockets: A single-welt chest pocket on the left front of the outer layer, with an interfaced welt topstitched close to the edge; in-seam pockets in the side seams.

Back: One piece cut on the fold in each layer, with no centre back seam.

Finishing: Front edges and collar topstitched after joining the layers; each layer has its own topstitched hem. The inner layer has no welt pocket.

Level Of Difficulty

Intermediate. A single-welt pocket, in-seam pockets, a shawl collar cut in one with the fronts, and two full layers joined along the front edges and collar.

Fabric Recommendations

Dense silk or cotton fabrics for both layers, in two colours or prints.

Additional Supplies

  • Contrasting fabric for the inner layer
  • Fusible interfacing (welt and a strip about 4 cm wide over the pocket marking)

Cutter's Must

From main fabric:

  • Back – 1 piece on fold
  • In Seam Pocket – 2 pieces
  • Breast Pocket – 2 pieces
  • Front – 2 pieces
  • Waistband – 1 piece
  • Sleeve – 2 pieces

From contrasting fabric:

  • Back – 1 piece on fold
  • In Seam Pocket – 2 pieces
  • Off-Set Welt – 1 piece on fold
  • Front – 2 pieces
  • Waistband – 1 piece
  • Sleeve – 2 pieces

Sewing Instructions

  1. Fuse interfacing to the Off-Set Welt. Fold the welt in half lengthwise, right sides together, stitch the short ends, turn it right side out and edge-stitch. On the wrong side of the outer Front, press a strip of interfacing about 4 cm wide over the pocket marking. Place the Off-Set Welt and the upper Breast Pocket bag on the Front, right sides together, pin along the pocket opening marking and stitch, making sure the long raw edges of the welt and the pocket bag meet at the centre line of the pocket marking. Cut the Front lengthwise between the stitching lines and diagonally into the ends of the stitching. Take care not to cut the welt and the pocket bags. Press the seam allowances open. Turn the welt and the pocket bag through the opening to the wrong side and baste. On the wrong side of the Front, place the lower Breast Pocket bag on the welt with the bag pointing upwards, and from the right side stitch the welt into its seam, catching the pocket bag. Press the pocket bag downwards. Turn the small triangles at the ends of the opening to the wrong side and stitch them down exactly from the ends of the upper stitching line to the ends of the lower one. Trim the pocket bags so that they are even and stitch them together.
  2. Stitch the side seams, leaving the pocket openings unstitched. Pin the In Seam Pocket bags to the seam allowances of the pocket openings on the wrong side, right sides together, and stitch exactly along the marked side seam lines. Press the pocket bags towards the front and stitch them together.
  3. Stitch the shoulder seams up to the corner. Clip the seam allowance diagonally into the corners. Stitch the centre back seam of the collar, which is cut in one with the Fronts. Stitch the collar to the back neckline. Press the seam allowances open.
  4. Stitch the Sleeve seams. Set the Sleeves into the armholes.
  5. Press the hem allowance to the wrong side, turn the raw edge under and topstitch.
  6. Make up the inner layer of the robe from the contrasting fabric in the same way as the outer layer, but without the welt pocket. Place the outer and inner layers right sides together and stitch along the front edges and the collar. Turn the robe right side out. Match the collar seams of both layers and stitch in the ditch. Topstitch the front edges and the collar. Fold the hem allowances of the Sleeves to the wrong side and press. Topstitch the Sleeve hems, joining the outer and inner Sleeves.
  7. Place the two Waistband pieces right sides together and stitch along the long edges and one short end. Turn right side out and press the edges. Turn in the open end and topstitch all around the Waistband a presser-foot width from the edge.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?