Criss-Cross Halter Maxi Dress
A floor-length women's halter dress with a lined bodice, straps cut in one with the front neckline facing that cross into a deep V, a trim band under the bust and a flared skirt with a double inverted pleat at the centre front. The straps fasten at the back neck with two buttons and rouleau loops.
When To Wear
- Evening receptions, summer weddings and formal dinners.
- Warm-weather events: the shoulders are left open.
Key Design Features
Silhouette: Fitted bodice, raised waistline, skirt flaring to the floor.
Length: Floor length, the back slightly longer than the front.
Neckline: Halter neckline with a deep V. Straps cut in one with the neckline facing overlap at the centre front.
Sleeves: Sleeveless, armholes faced with the lining.
Front: Bodice fronts shaped with darts; a lower front cut on the fold with a double inverted pleat at the centre.
Back: Interfaced upper back joined to a lower back with a centre seam.
Closure: Concealed zipper in the centre back seam of the skirt; two buttons on the right strap and two rouleau loops on the left strap at the back neck.
Waist: Trim band at the front and back set into the skirt seam and pressed up over it; the shiny side of satin can face out on the trim.
Finishing: Back skirt hem finished with a shaped facing, front hem turned up and blind-stitched.
Lining: Bodice fronts and upper back are lined.
Level Of Difficulty
Intermediate. Faced straps with rouleau loops, a lined bodice, a set-in trim band, a concealed zipper and a hem facing on soft fabric.
Fabric Recommendations
Soft, well-draping fabrics from natural and blended fibres, such as crepe-satin.
Additional Supplies
- Lining fabric
- Fusible interfacing (straps and neckline facings, fronts, upper back, trim bands, back hem facing)
- Zipper
- 2 buttons
Cutter's Must
From main fabric:
- Upper Back – 2 pieces
- Lower Back – 2 pieces
- Front – 2 pieces
- Lower Front – 1 piece on fold
- Front Neckline And Strap Facing – 4 pieces
- Back Trimming – 2 pieces
- Front Trimming – 2 pieces
- Back Hem Facing – 2 pieces
- Bias Tape – 1 piece
From lining fabric:
- Upper Back – 2 pieces
- Front – 2 pieces
- From fusible interfacing: Front Neckline And Strap Facing, Front, Upper Back, Back Trimming, Front Trimming, Back Hem Facing.
Sewing Instructions
- Fuse interfacing to the Front Neckline And Strap Facing, Front, Upper Back, Back Trimming, Front Trimming and Back Hem Facing pieces.
- Stitch the darts on the Front pieces in main fabric and in lining. Stitch the side seams of the Front and Upper Back. Place the lining and the main fabric right sides together and stitch the armhole edges and the top edges of the back. Turn the lining to the wrong side and stitch it to the seam allowance 1 mm from the seam. Baste the front, back and lower edges together.
- From the Bias Tape, make a narrow rouleau, cut it in half and form each piece into a loop.
- Place one Front Neckline And Strap Facing on each Front half, right sides together, and stitch at the markings. Press the seam allowance towards the strap. Baste the loops to the end of the left strap: the tops of the loops lie on the strap and the ends on the seam allowance. Place the remaining Front Neckline And Strap Facing pieces on the attached ones, right sides together, and stitch along the neckline and strap edges. Trim the seam allowances and cut the corners diagonally. Turn the straps right side out and baste along the edges. Turn under the open edges and sew them by hand over the joining seam.
- Stitch the centre back seam of the Lower Back, leaving an opening for the zipper. Stitch the side seams, stopping 10 cm above the hemline. Fold and baste the double inverted pleat on the Lower Front.
- Stitch the centre front and side seams of the Front Trimming and Back Trimming. When stitching the centre front seam, leave the seam allowances at the top and bottom edges free. Place the trim on the skirt, right sides together, and stitch at the markings, with the trim pointing downwards! Press the trim upwards. Baste the top edges of the skirt and trim together. Stitch the skirt to the bodice.
- Press the seam allowances of the zipper opening to the wrong side. Place the zipper under the edges of the opening and stitch so that the teeth are hidden, turning under the ends of the tape.
- Stitch the centre back seam of the Back Hem Facings. Place the facing on the Lower Back, right sides together, and stitch along the lower edge. Turn the facing back, stitch it to the seam allowance and press. Stitch the open parts of the side seams and, without breaking the stitching, stitch the side edges of the facing to the hem allowance of the Lower Front. Turn the facing and the hem allowance to the wrong side and hem with blind stitches.
- Sew the buttons onto the right strap to match the loops.