Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#2783
#2785

Raglan Sleeve Zippered Stand Collar Jacket

Pattern #2784

A hip-length women's jacket in low-stretch knit, with two-piece raglan sleeves, a stand collar cut in one with the front and back, and a separating zipper the full length of the centre front. Drafted to your own measurements. Recommended fabric: low-stretch knit fabric from natural or blended fibres.

Tech. Description

Raglan Sleeve Zippered Stand Collar Jacket

A hip-length women's jacket in low-stretch knit, with two-piece raglan sleeves, a stand collar cut in one with the front and back, and a separating zipper the full length of the centre front.

When To Wear

  • In spring and autumn as a light outer layer over tops and thin knitwear.
  • With trousers, jeans or straight skirts for everyday and office wear.

Key Design Features

Silhouette: Straight, shaped at the front by bust darts pressed upwards.

Length: Hip length.

Collar: Stand collar cut in one with the front and back, faced by the front facings and the back neck facing.

Sleeves: Raglan, each sleeve cut in two parts (front and back) joined by an overarm seam that stops at a mark and leaves a slit at the hem. Below-elbow length; small raglan shoulder pads.

Closure: Separating zipper set between the fronts and the facings, from the top of the stand to the hem.

Back: Centre back seam running up through the stand.

Finishing: Sleeve and side seams stitched in one pass; hem and sleeve hems turned up 3 cm and blind-stitched, slit allowances blind-stitched by hand.

Level Of Difficulty

Intermediate. A zipper inserted between garment and facing, a cut-on stand collar, raglan sleeves with a hem slit, and shoulder pads, all in knit fabric.

Fabric Recommendations

Low-stretch knit fabric from natural or blended fibres.

Additional Supplies

  • Fusible interfacing (front facings, back neck facing)
  • Small raglan shoulder pads
  • Separating zipper

Cutter's Must

If the patterns have a double contour, seam allowances are included. If the contour is single, the patterns are without seam allowances. Seam allowances: all seams 1 cm. Hem allowance for the bottom of the garment and sleeve hem – 3 cm. Allowance along the sleeve slit – 3 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90cm to 150cm) to determine how much material you will need (do not forget to account for paired and symmetrical pieces). When stitching pieces, pay attention to the notches - they must match!

  • From main fabric:
    • Back – 2 pieces
    • Front – 2 pieces
    • Back Sleeve – 2 pieces
    • Front Sleeve – 2 pieces
    • Center Front Facing – 2 pieces
    • Back Neckline Facing – 2 pieces
  • From fusible interfacing:
    • Center Front Facing – 2 pieces
    • Back Neckline Facing – 2 pieces

Sewing Instructions

  1. Fuse interfacing to the Center Front Facings and Back Neckline Facings.
  2. Stitch the darts on the Front, press the dart intake upwards.
  3. Stitch the center back seam, press allowances to the left side, serge.
  4. Stitch the Back Sleeves to the Back along the raglan seams, press the allowances towards the sleeve, serge. Stitch the Front Sleeves to the Fronts, press the allowances towards the sleeve, serge.
  5. Serge the overarm edges of the sleeves separately. Stitch the overarm seam from the neckline down to the slit mark, press the allowances open. Stitch the underarm sleeve seams and side seams in one continuous seam, press allowances towards the back, serge. Sew in shoulder pads.
  6. Stitch the center seam of the Back Neckline Facings, press the allowances open. Stitch the shoulder seams joining the Center Front Facings to the Back Neckline Facing, press allowances open. Serge the outer edge.
  7. Place the facings on the garment right sides together and stitch the front edges, the edge of the one-piece stand collar, and the bottom corners, inserting the separating zipper between the pieces.
  8. Serge the hem allowance of the garment and sleeve, press to the wrong side and hem with blind stitches. Hem the allowances of the sleeve slit with blind stitches.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?