Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4241
#4243

Blazer with Wide Collar and Asymmetric Closure

Pattern #4242

A fitted, fully lined women's jacket at high-hip length with an asymmetric buttoned front, curved seams across the right front, a wide collar and two-piece sleeves. Drafted to your own measurements. Recommended fabric: suiting fabric from natural or blended fibres.

Tech. Description

Blazer with Wide Collar and Asymmetric Closure

A fitted, fully lined women's jacket at high-hip length with an asymmetric buttoned front, curved seams across the right front, a wide collar and two-piece sleeves.

When To Wear

  • Over dresses and sheath skirts to the office.
  • With trousers and a fine knit for autumn and spring days.

Key Design Features

Silhouette: Fitted, shaped by princess seams and darts on the front and back.

Length: High hip, with a rounded front edge at the hem.

Collar: Wide interfaced collar, its ends sewn into the front edge so it wraps across to the closure.

Front: Asymmetric. The right centre front is made of three pieces joined by curved seams, with buttonholes left open in these seams; the remaining buttonholes are worked by machine. Buttons sewn to the left front.

Sleeves: Long two-piece set-in sleeves with elbow and front seams, eased sleeve cap, sleeve heads.

Back: Centre back seam, princess seams and darts.

Finishing: Front edges, neckline and hem finished with interfaced facings (front facing, back neck facing and back hem facing); shoulder pads.

Lining: Full lining including sleeves, bagged through an opening in the right sleeve seam.

Level Of Difficulty

Advanced. In-seam buttonholes matched between the front and the pieced facing, curved seams, a facing that runs round the whole edge and hem, set-in two-piece sleeves and a bagged lining.

Fabric Recommendations

Suiting fabric from natural or blended fibres.

Additional Supplies

  • Lining fabric
  • Fusible interfacing (centre fronts, facings, collar)
  • 5 buttons
  • Shoulder pads
  • Sleeve heads

Cutter's Must

If the patterns have a double contour, they include seam allowances. If the contour is single, the patterns do not include seam allowances. Seam allowances: all seams 1 cm. Hem allowance for sleeve hem – 3.5 cm. Attention! First of all, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need (do not forget to account for paired and symmetrical pieces). When stitching pieces, pay attention to the notches - they must match! Labels on the pattern pieces are written on the right side!

From main fabric:

  • Center Back – 2 pieces
  • Side Back – 2 pieces
  • Side Front – 2 pieces
  • Center Right Piece Front 1 – 1 piece
  • Center Right Piece Front 2 – 1 piece
  • Center Right Piece Front 3 – 1 piece
  • Center Left Front – 1 piece
  • Collar – 2 pieces
  • Left Center Front Facing – 1 piece
  • Right Edge Facing 1 – 1 piece
  • Right Edge Facing 2 – 1 piece
  • Right Edge Facing 3 – 1 piece
  • Back Neckline Facing – 1 piece
  • Back Hem Facing – 1 piece
  • Upper Sleeve – 2 pieces
  • Lower Sleeve – 2 pieces

From lining fabric:

  • Front Lining – 2 pieces
  • Side Front – 2 pieces
  • Center Back – 2 pieces
  • Side Back – 2 pieces
  • Upper Sleeve – 2 pieces
  • Lower Sleeve – 2 pieces

The lining Center Back, Side Back and Side Front pieces are cut minus the width of the back neckline facing, back hem facing and front facing.

From fusible interfacing:

  • Center Right Piece Front 1 – 1 piece
  • Center Right Piece Front 2 – 1 piece
  • Center Right Piece Front 3 – 1 piece
  • Center Left Front – 1 piece
  • Collar – 1 piece
  • Left Center Front Facing – 1 piece
  • Right Edge Facing 1 – 1 piece
  • Right Edge Facing 2 – 1 piece
  • Right Edge Facing 3 – 1 piece
  • Back Neckline Facing – 1 piece
  • Back Hem Facing – 1 piece

Sewing Instructions

  1. Fuse interfacing to the pieces listed above.
  2. On the Center Back pieces, stitch the darts and press them towards the centre. Stitch the back princess seams (Center Back to Side Back) and press them open. Stitch the centre back seam and press it open.
  3. Stitch the dart on the Center Left Front and press it upwards. Stitch the left front princess seam (Center Left Front to Side Front) and press the seam allowances towards the side seam.
  4. Place Center Right Piece Front 1 on Center Right Piece Front 2, right sides together, and stitch from the front edge to the start of the buttonhole and from the end of the buttonhole to the armhole edge. Press the seam allowances open. Join Center Right Piece Front 2 and Center Right Piece Front 3 in the same way, leaving the buttonhole open. Press the seam allowances open. Stitch the right front princess seam (to the Side Front) and press the seam allowances towards the side seam.
  5. Stitch the shoulder and side seams of the jacket and press them open.
  6. Place the Collar pieces right sides together and stitch the outer edge. Clip the seam allowances. Turn the collar right side out, ease out the edge and press. Stitch the collar to the jacket neckline and baste the collar ends to the front edge.
  7. Place Right Edge Facing 1 on Right Edge Facing 2, right sides together, and stitch from the front edge to the start of the buttonhole and from the end of the buttonhole to the inner edge. Press the seam allowances open. Join Right Edge Facing 2 and Right Edge Facing 3 in the same way, leaving the buttonhole open. Press the seam allowances open.
  8. Stitch the shoulder seams of the Back Neckline Facing and the front facings (Left Center Front Facing and the joined right edge facing) and press them open. Stitch the Back Hem Facing to the front facings. Press the seam allowances open.
  9. Place the joined facings on the jacket, right sides together, pin, and stitch along the front edges, the front and back neckline and the jacket hem, stitching from the jacket side. Clip the seam allowances on the curves and trim the corners. At each in-seam buttonhole, stitch the seam allowances of the front and the facing together, continuing the seam line.
  10. Stitch the elbow seam of the sleeve (Upper Sleeve to Lower Sleeve) and press it open. Press up the sleeve hem. Stitch the front sleeve seam and press it open.
  11. Set the sleeves into the armholes, matching the notches and easing the sleeve cap. Attach the shoulder pads and sleeve heads.
  12. Sew the lining pieces together and set in the lining sleeves, leaving an opening in the front seam of the right sleeve. Stitch the lining to the inner edges of the front facings and the back facings. Press the collar seam allowances open and tack them together close to the seams. Stitch the lining to the sleeve hems. Turn the jacket right side out through the opening in the sleeve. Stitch the opening closed.
  13. Make the remaining buttonholes on the right front and sew the buttons on the left front.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?