Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4232
#4234

Jacket with Pleated Front Overlay and Peplum

Pattern #4233

A fitted, waist-length women's jacket with a stand collar, curved double-layer front panels pleated into the neckline, and a pleated peplum set into the waist seam. Long set-in sleeves, edge-to-edge front fastened with hooks and eyes, fully lined. Drafted to your own measurements. Recommended fabric: lightweight suiting in natural or blended fibres.

Tech. Description

Jacket with Pleated Front Overlay and Peplum

A fitted, waist-length women's jacket with a stand collar, curved double-layer front panels pleated into the neckline, and a pleated peplum set into the waist seam. Long set-in sleeves, edge-to-edge front fastened with hooks and eyes, fully lined.

When To Wear

  • To the office over a dress or with a narrow skirt or trousers.
  • In spring and autumn as a light lined jacket.

Key Design Features

Silhouette: Close-fitting through the bodice, flaring out below the waist into the peplum.

Length: Peplum ends at the hip.

Collar: Stand collar cut in two layers, joined at the front edges.

Front: Princess seams; a curved decorative panel cut double sits on top of each front, its rounded edge left free, its neckline edge folded into five pleats.

Closure: Edge-to-edge front with 5 hooks and eyes.

Sleeves: Long, one-piece set-in sleeves with shoulder pads and sleeve heads.

Back: Princess seams, darts and a centre back seam.

Waist: Peplum cut in one piece on the fold, pleated at the top and sewn in between the jacket and the lining.

Lining: Full lining of the body and sleeves, attached to the front facings and back neck facing.

Level Of Difficulty

Advanced. Layered pleated front panels inserted into princess seams, a two-layer stand collar, a fully lined jacket bagged out through the sleeve seam, shoulder pads and sleeve heads.

Fabric Recommendations

Lightweight suiting in natural or blended fibres.

Additional Supplies

  • Lining fabric
  • Fusible interfacing (centre fronts, front facings, back neck facing, collar stand, sleeve hem allowances)
  • Shoulder pads
  • Sleeve heads
  • 5 hooks and eyes

Cutter's Must

If the patterns have a double contour, they include seam allowances. If the contour is single, the patterns do not include seam allowances. Seam allowances: all seams 1 cm. Hem allowance for sleeve hem 3 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need (do not forget to account for paired and symmetrical pieces). When stitching pieces, pay attention to the notches - they must match!

From main fabric:

  • Center Back – 2 pieces
  • Side Back – 2 pieces
  • Center Front – 2 pieces
  • Side Front – 2 pieces
  • Stand Collar – 2 pieces
  • Sleeve – 2 pieces
  • Back Neckline Facing – 1 piece
  • Center Front Facing – 2 pieces
  • Decorative Front – 4 pieces
  • Peplum – 1 piece on fold

From lining fabric:

  • Center Back – 2 pieces
  • Center Front – 2 pieces
  • Side Back – 2 pieces (cut from the main fabric pattern)
  • Side Front – 2 pieces (cut from the main fabric pattern)
  • Sleeve – 2 pieces (cut from the main fabric pattern)

From fusible interfacing:

  • Center Front
  • Back Neckline Facing
  • Sleeve hem allowance
  • Center Front Facing
  • Stand Collar

Sewing Instructions

  1. Fuse interfacing to the Center Front, Center Front Facing, Back Neckline Facing and Stand Collar pieces. Interface the back neckline edge and the sleeve hem allowances.
  2. On the Center Back pieces, stitch the darts and press them towards the centre. Stitch the back princess seams (Center Back to Side Back) and press the allowances open. Stitch the centre back seam and press the allowance open.
  3. Place the Decorative Front pieces right sides together in pairs and stitch along the free rounded edge between the round marks. Clip the allowance at the mark. Turn the pieces right side out. Stitch the front princess seam (Center Front to Side Front), inserting the decorative front. Align the neckline edges (the extended neckline edge of the decorative front remains free). Fold the free part of the neckline edge into five pleats and baste 0.5 cm from the edge.
  4. Stitch the side and shoulder seams of the jacket and press them open.
  5. Stitch the sleeve seam. Press the allowance towards the back. Set the sleeve into the armhole, matching the notches. Attach the shoulder pads and sew in the sleeve heads.
  6. Stitch the outer Stand Collar to the neckline. Press the allowances open.
  7. Sew the lining pieces together and set in the lining sleeves, leaving an opening in one sleeve seam. Stitch the shoulder seams of the Center Front Facings and the Back Neckline Facing. Press the allowances open. Stitch the lining to the facings. Stitch the inner Stand Collar to the facing neckline. Press the allowance open.
  8. Lay the pleats on the Peplum and baste them 0.5 cm from the edge. Stitch the front ends of the peplum. Turn it right side out.
  9. Place the jacket and the lining right sides together and stitch along the front edges and the stand collar. Stitch the lower edge of the jacket to the lower edge of the lining, inserting the peplum between them. Turn the jacket right side out and ease out the seams. Through the opening in the sleeve, tack the neckline seams of the outer and inner collar together. Stitch the lining to the sleeve hems. Close the opening.
  10. Sew on the hooks and eyes.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?