Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4140
#4142

Draped One-Shoulder Maxi Dress

Pattern #4141

A long women's dress for knit fabric with a one-shoulder draped bodice: a loose blouson overlayer with a twisted shoulder band falls over a fitted strapless under-top with elastic at the upper edge, and the bodice joins a straight skirt at an elasticated waist seam. Drafted to your own measurements. Recommended fabric: well-draping knit of medium stretch, from natural or blended fibres.

Tech. Description

Draped One-Shoulder Maxi Dress

A long women's dress for knit fabric with a one-shoulder draped bodice: a loose blouson overlayer with a twisted shoulder band falls over a fitted strapless under-top with elastic at the upper edge, and the bodice joins a straight skirt at an elasticated waist seam.

When To Wear

  • Evening events, dinners and weddings as a guest.
  • Summer holidays and warm evenings, with flat sandals or heels.

Key Design Features

Silhouette: Blouson bodice gathered into a low-set waist seam, narrow straight skirt below.

Length: Long, to the lower calf or ankle.

Neckline: Asymmetric one-shoulder line. The upper front and back are cut on the fold and seamed into one drape; on the shoulder the corner sections are turned through and twisted into a band, then set into the upper edge, so the fabric falls in soft folds over the arm.

Sleeves: None; the armhole of the double-layer drape is stitched and turned through.

Front: Inner strapless top with darts, its upper edge finished with 2 cm elastic. The overlayer is gathered along its lower edge and joined to the top.

Waist: 0.5 cm elastic zigzagged to the wrong side of the skirt along the bodice seam; no zip or fastening.

Skirt: Two pieces, front and back, joined at the side seams.

Finishing: Seams sewn with an elastic or narrow zigzag stitch or on an overlocker; hem overlocked, turned and topstitched, twin needle or coverstitch recommended.

Level Of Difficulty

Advanced. A drape assembled in stages by notches and marks, turned-through and twisted shoulder sections, an elasticated inner top and gathering on knit fabric.

Fabric Recommendations

Well-draping knit of medium stretch, from natural or blended fibres.

Additional Supplies

  • Elastic 2 cm wide (upper edge of the inner top)
  • Elastic 0.5 cm wide (waist seam)

Cutter's Must

If the patterns have a double contour, they include seam allowances. If the contour is single, the patterns do not include seam allowances. Seam allowances: hem allowance – 1.5 cm, top upper edge allowance – 2.5 cm, other seams 0.8 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need. Inscriptions on the patterns are on the right side!

  • Upper Back – 1 piece on fold
  • Upper Front – 1 piece on fold
  • Skirt – 2 pieces
  • Front Top – 1 piece
  • Back Top – 1 piece

Tip: Cut pieces from knit fabrics are stitched with a special elastic or narrow zigzag stitch. The hem allowance is topstitched with a twin needle or on a coverstitch machine to maintain elasticity. You can also stitch pieces directly on a 3- or 4-thread overlocker.

Sewing Instructions

When stitching pieces, pay attention to the notches - they must match!

  1. Stitch the side seams of the Skirt. Press the allowances towards the back and overlock.
  2. Stitch the darts on the Front Top. Trim the dart excess with an overlocker. Stitch the side seams of the Front Top and Back Top. Press the allowances towards the back and overlock. Stitch the 2 cm wide elastic, with a slight overlap at the ends, to the upper edge of the top. Fold the allowance together with the elastic downwards and topstitch with an elastic stitch (or on a coverstitch machine).
  3. Lay out the Upper Back and Upper Front in a single layer and stitch the side seam separately on the outer and on the inner side. Press the seams. Fold the pieces right sides together and stitch the armhole edges together. Turn the pieces right side out and press.
  4. Lay out the pieces in a single layer in section “3”, fold the back and front right sides together and stitch this section between the notches. Press the seam, turn the pieces right side out.
  5. Fold the Upper Front right sides together and stitch the corner between the notches in the upper part of the piece on a straight-stitch machine. Clip the allowances near the notches, turn the piece right side out. Sew the corner on the Upper Back in the same way. Twist the bands as shown in the drawing.
  6. Lay out the pieces in a single layer. Fold the back and front right sides together along section “2” and stitch. Press the seam. Fold the pieces in half lengthwise.
  7. Stitch the section between the round marks. To do this, fold the pieces right sides together and, after checking that the piece can still be turned through afterwards, stitch the section. Turn the piece right side out and press.
  8. Stitch the band to the upper edge of the back and front, matching the notches.
  9. Along the lower edge of the Upper Front, sew a row of loosely tensioned stitches and gather. Match the lower edges of the Upper Back and Upper Front with the top. Stitch the pieces to the Skirt.
  10. Zigzag the 0.5 cm wide elastic to the wrong side of the Skirt along the seam joining the bodice.
  11. Overlock the lower edge of the garment. Press to the wrong side and topstitch.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?