Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4214
#4217

Collared V-Neck Dolman Sleeve Dress

Pattern #4216

A knee-length women's dress in knit fabric with short cut-on sleeves, a V-neckline with a collar, soft pleats above and below a waist insert, and side pockets in curved front seams. Drafted to your own measurements. Recommended fabric: soft knit fabric with low to medium stretch, such as jersey.

Tech. Description

Collared V-Neck Dolman Sleeve Dress

A knee-length women's dress in knit fabric with short cut-on sleeves, a V-neckline with a collar, soft pleats above and below a waist insert, and side pockets in curved front seams.

When To Wear

  • For the office and daytime events in spring, summer and early autumn.
  • With a wide belt over the waist insert.

Key Design Features

Silhouette: Fitted through the waist with a separate waist insert at front and back; the skirt narrows slightly towards the hem.

Length: Knee length.

Collar: Standing collar that turns down at the front, attached to the neckline and finished with front facings and back neckline facings; it opens into a V at the centre front.

Sleeves: Short dolman sleeves cut in one with the upper front and upper back; no armhole seam.

Front: Upper front in two pieces with soft pleats directed towards the side seams above the waist insert; lower front cut on the fold with soft pleats gathered into the insert.

Pockets: Pockets with curved openings between the lower front and the side front pieces, with pocket bags.

Back: Centre back seam through the upper and lower back, with a waist insert between them.

Finishing: Dress and sleeve hems serged, turned and topstitched with a twin needle.

Level Of Difficulty

Intermediate. Sewing knit fabric with an elastic or narrow zigzag stitch, pleats on a curved panel, a collar set with facings, pockets in a shaped seam.

Fabric Recommendations

Soft knit fabric with low to medium stretch, such as jersey.

Additional Supplies

  • Fusible interfacing (collar)

Cutter's Must

If the patterns have a double contour, they include seam allowances. If the contour is single, the patterns do not include seam allowances. Seam allowances: Hem allowance for the garment and sleeve hem – 2 cm, other seams 1 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need.

From main fabric:

  • Upper Back – 2 pieces
  • Lower Back – 2 pieces
  • Upper Front – 2 pieces
  • Lower Front – 1 piece on fold
  • Front Inset – 1 piece
  • Back Inset – 1 piece
  • Collar – 2 pieces
  • Front Facing – 2 pieces
  • Back Neckline Facing – 2 pieces
  • Side – 2 pieces
  • Pocket Bag – 2 pieces

From fusible interfacing:

  • Collar (under collar only) – 1 piece

Tip: Knit fabric pieces are stitched with a special elastic or narrow zigzag stitch. When serging, trim seam allowances to 0.6 – 0.8 cm. The hem allowance is topstitched with a twin needle to maintain elasticity.

Sewing Instructions

When stitching pieces, pay attention to the notches - they must match!

  1. Fuse interfacing to the undercollar.
  2. Stitch the center seams of the upper back and lower back. Press the seams to the left side and serge. Attach the back inset to the upper back and lower back. Press the seams towards the inset and serge.
  3. On the upper front, lay soft pleats according to the markings and secure them at the lower edge. The pleat depths are directed towards the side seam.
  4. Stitch the back neckline facings to the front facings in pairs. Press seams open. Set the collars into the necklines (the undercollar into the garment neckline, the upper collar into the facing neckline). Clip the seams and press open.
  5. Stitch the center seam of the front facings from the mark to the bottom on a straight stitch machine. Clip the seams at the mark and press open. Place the facings with the collar right sides together with the fronts and stitch, starting from the mark, along the front edge and around the collar. Turn the pieces right side out and press. Secure the seam allowances of the upper collar and undercollar together close to the stitching line. Secure the outer edges of the front facings and back neckline facings to the garment and then treat them as one piece.
  6. Stitch the shoulder seams of the upper back and upper front. Press seams towards the back and serge.
  7. Attach the front facings with the back neckline facings to the back and front. Press seams towards the back and front. Attach the front inset to the upper front. Press the seam towards the inset and serge.
  8. Place the pocket bag on the lower front right sides together and stitch the pocket opening. Clip the seams, turn the pieces right side out and press. Fold the lower front onto the side piece according to the markings and align the edges. Stitch and serge the pocket bag edges.
  9. Lay soft pleats on the lower front: the pleat depths are directed towards the side seams. It is recommended to lay the pleats starting from the side seam. Attach the front inset to the lower front. Press the seam towards the inset and serge.
  10. Stitch the side seams. Press seam allowances towards the back and serge.
  11. Serge, fold and topstitch the bottom edge of the dress and the bottom edge of the sleeve. The dress is recommended to be worn with a wide belt.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?