Professional made-to-measure digital sewing patterns — PDF · PLT · DXF AAMA

Minervainervabeta
#4075
#4077

Stand Collar Ruffled Long Sleeve Blouse

Pattern #4076

A semi-fitted women's blouse for knit fabric, hip length, with a stand collar and a buttoned half placket framed by three layers of gathered ruffles on each side. The back has a yoke and a centre back seam; the side seams open into slits at the hem. Drafted to your own measurements. Recommended fabric: medium or high stretch knit fabric of natural or blended fibres.

Tech. Description

Stand Collar Ruffled Long Sleeve Blouse

A semi-fitted women's blouse for knit fabric, hip length, with a stand collar and a buttoned half placket framed by three layers of gathered ruffles on each side. The back has a yoke and a centre back seam; the side seams open into slits at the hem.

When To Wear

  • At the office with trousers or a pencil skirt, worn loose over the waistband.
  • Under a jacket or cardigan in autumn and winter.

Key Design Features

Silhouette: Semi-fitted, shaped by front darts.

Length: To the hip, with side slits.

Collar: Stand collar, interfaced upper stand.

Front: One front piece cut on the fold, slashed for a half placket. The two interfaced plackets are folded lengthwise and topstitched 0.1 cm from the ruffle seam. Buttonholes on the right, buttons on the left. Three ruffles on each side, layered, edged with a rolled hem and gathered along the inner edge into the placket seam.

Sleeves: Long one-piece set-in sleeves with a turned and topstitched hem.

Back: Yoke across the shoulders and a centre back seam.

Finishing: Hem and slit edges turned to the wrong side and topstitched.

Level Of Difficulty

Intermediate. Sewing knit fabric, gathering and setting layered ruffles, a slashed half placket, a stand collar and side slits.

Fabric Recommendations

Medium or high stretch knit fabric of natural or blended fibres.

Additional Supplies

  • 5 buttons
  • Fusible interfacing (plackets, upper collar stand)

Cutter's Must

If the patterns have a double contour, they include seam allowances. If the contour is single, the patterns do not include seam allowances. Seam allowances: hem and sleeve hem allowance – 1.5 cm. Other seams 0.8 cm. Attention! First, print out the paper patterns and lay them out on the fabric width (fabric width can be from 90 cm to 150 cm) to determine how much material you will need. When stitching pieces, pay attention to the notches - they must match!

From main fabric:

  • Front – 1 piece on fold
  • Back – 2 pieces
  • Yoke – 1 piece
  • Sleeve – 2 pieces
  • Placket – 2 pieces
  • Ruche 1 – 2 pieces
  • Ruche 2 – 2 pieces
  • Ruche 3 – 2 pieces
  • Stand Collar – 2 pieces

From fusible interfacing:

  • Placket – 2 pieces
  • Upper Stand Collar – 1 piece

Sewing Instructions

Tip: Knit fabric pieces are stitched with a special elastic or narrow zigzag stitch. The hem allowance is topstitched with a twin needle or on a coverstitch machine to maintain elasticity. You can also stitch pieces directly on a 3- or 4-thread overlocker.

  1. Stitch darts on the front. Trim the dart folds with an overlocker.
  2. Stitch the center back seam. Overlock the seam allowance and press to the left side.
  3. Attach the yoke to the back. Overlock seam allowances and press downwards.
  4. Stitch shoulder seams. Overlock seam allowances and press towards the back.
  5. Overlock the outer and lower edges of each ruche (ruffle) with a rolled hem. Place ruche 2 right side up on ruche 3, then place ruche 1 on top. Along the inner edge of the ruches, stitch with a loosened upper thread and gather. Attach the ruches to the front. Fold plackets in half lengthwise and attach to the front. Slash the front at the corners to the mark. Press placket allowances inwards and secure from the inside with stitching. Topstitch the placket 0.1 cm from the ruche attachment seam.
  6. Fold the stand collar pieces right sides together and stitch along the upper edge. Start and end stitching strictly at the marked collar attachment line. Attach the outer stand collar to the neckline. Fold the allowance of the inner stand collar inwards and topstitch.
  7. Set sleeves into armholes, matching marks. Overlock seam allowance.
  8. On the front, overlock the section from the bottom to the slit mark. Stitch the sleeve seam and side seams up to the slit mark. Overlock seam allowances and press towards the back.
  9. Overlock the lower edge of the sleeve. Fold to the wrong side, press and topstitch.
  10. Overlock the lower edge of the blouse. Fold to the wrong side, press and topstitch. Press allowances along the slits to the wrong side and topstitch.
  11. On the right front, make buttonholes, on the left, sew on buttons.

Features

Order Pattern

Standard Sizes

Individual Measurements

Please double-check the file format and paper size. Your pattern is drafted in exactly the format you select; a different format or paper size later is a new order.

Similar patterns

View all
Support

Minerva Support

Online
Support
Hi! I'm Minerva's AI assistant. What can I help you with?